Question about 2001 GMC Denali

Open Question

2008 chevolet impala windshield washer fluid level reads low when resevoir is full

Posted by Anonymous on

Ad

5 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 5 Answers

SOURCE: WINDSHIELD WASHER

how bad is it leaking?if its' a small leak maybe duct tape it if you dont really want to replace it.maybe that would get you by for awhile...

Posted on Jan 08, 2009

Ad
airjer995

Jeremy W.

  • 5332 Answers

SOURCE: front windshield washer won't work. Full of fluid.

Check the washer pump. It is located under the air cleaner assembly. There will be a connector with tow terminals. there should be power on the red wire anytime the washer button is pressed. There should be ground on the black wire at all times. If there is no power than check the washer fluid fuse and relay in the underhood fuse block. If there is power than the pump is probably bad.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Posted on Sep 28, 2010

bonedivers

Steve Newton

  • 1140 Answers

SOURCE: I ACCIDENTALLY PUT WINDSHIELD WASHER FLUID IN MY

why were you adding fluid? could be a leak causing your overheat issue.

Posted on May 20, 2011

canwoodjc

Canwoodjc

  • 3301 Answers

SOURCE: windshield washer fluid lamp will not shut off. It

sometimes that takes a few starts and stops, if it doesn't clear in a couple of days unhook the battery wait 5 minutes and hook it back up

Posted on Jul 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

Tip

Adding windshield washer fluid to Buick Lacrosse 2005


When the windshield washer fluid is low, a low washer fluid light may appear on the instrument panel cluster. In addition, if your vehicle is equipped with a Driver Information Center (DIC), the LOW WASHER FLUID message will appear when the fluid level is low. When you need windshield washer fluid, be sure to read the manufactures instructions before use. If you will be operating your vehicle in an area where the temperature may fall bellow freezing, use a fluid that has sufficient protection against freezing.

on Oct 08, 2010 | Buick LaCrosse Cars & Trucks

1 Answer

2008 impala windshield washer dic reset


You have a bad sensor. It's on the washer reservoir. This is a 2003 pic, But gives you an idea where to look. The sensor is the one on the right.0b881713-956c-40a5-a1eb-b595b40be6e8.gif

May 15, 2014 | 2008 Chevrolet Impala SS

1 Answer

My windshield washer fluid won't spray. I filled the resevoir today but I don't think it was empty My windshield wipers work just fine


You have a sensor on your washer fluid system. Make sure it hasn't been unpluged. It might not be getting voltage.

Jan 10, 2011 | 2006 Chevrolet Impala

3 Answers

What does "low wash" mean on a 2007 dodge ram?


This indicates that your windshield washer fluid level is low. It's like the low fuel light, it gives you times to get some before you run out. If you check the washer fluid level and it is not low then the sensor is faulty.

best wishes

Jan 02, 2011 | 2007 Dodge Ram 1500 Quad Cab Sport

1 Answer

Windshield Washer Pump Works But No Fluid Flow


May be the resevoir bottle may have something stuck in it, you are right, you may have a clogged line. Also check the routing of the hoses to the squirt that they are not pinched or kinked. Any washer fuild leaking anywhere?

Mar 13, 2010 | 1998 Mitsubishi Montero Sport

2 Answers

Wiper fluid level sensor replacement


Reservoir —Windshield Wiper

Removal
  1. Remove the RH wheel; refer to Section 204-04 .
  1. Position RH splash shield aside.
    1. Remove six screws.
    1. Remove three pin-type retainers.
    1. Position RH splash shield aside.
  1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
    Disconnect the electrical connector and washer hoses.
  1. Remove the upper reservoir bolt.
  1. Remove the windshield washer reservoir.
    • Loosen the two lower reservoir bolts.
------------------------------------------------------------------------------------

Jan 15, 2009 | 2000 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...