How to replace a power steering hose Chevrolet Silverado 2500HD

SOURCE: 2001 chevy sylverado 2500hd power steering and power brakes quit

check power steering fluid. first. if all good . power steering is going. your hydro boost brake system depends on the power steering pump if it goes out your brake go out.

SOURCE: 2005 Chevrolet Silverado 2500HD 4x4 Oil Change Reset

Not positive 05 is the same but on my 02 you turn the key to the on position and pump the gas pedal 4 times.

SOURCE: How do I change the cabin filter on 2002 Chevrolet

The air filter is located under the hood, passenger side, up by the windshield. it has a small retangular cover about 3 X 10 that pulls off

SOURCE: 2003 CHEVROLET SILVERADO 2500HD 6.0

4.8L, 5.3L & 6.0L Engines

1. Remove the air inlet duct.
   
2. Drain the cooling system.
   
3. Remove the radiator outlet hose.
   
4. Remove the thermostat housing bolts.
   
5. Remove the thermostat from the water pump housing.
   

The O-ring seal is integral to the thermostat housing

Thermostat housing-4.8L, 5.3L and 6.0L engines

To install:

1. Install the thermostat to the water pump housing making sure the spring side is inserted into the engine.
   
2. Install the bolts.
   
   • Tighten the bolts to 11 ft. lbs. (15 Nm).
     
3. Install the radiator outlet hose.
   
4. Fill the cooling system.
   
5. Install the air inlet duct.
   
6. Test the system for leaks.
   

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 26; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

SOURCE: how to change 2004 Chevrolet Silverado 2500HD

Welcome to FIxYa.com

Bumper Replacement - Front (Old Style)

Removal Procedure

1. Remove the front grille.

Image ---1

2. Disconnect the electrical connector from the fog lamps, if equipped.

Image---2

3. Remove the retaining bolts (1,2) from the front bumper.

4. Remove the brace bolt (3) from the front bumper.

5. Remove the front bumper assembly from the vehicle.

6. Remove the air deflector from the bumper if necessary.

7. Remove the fog lamps, if equipped.

Installation Procedure

1. Install the fog lamps, if equipped.

2. Install the air deflector to the bumper if necessary.

3. Position the front bumper assembly on the vehicle.

Image---3

Notice: Refer to Fastener Notice in Service Precautions.

Important: Tighten the bolts in the following sequence.

4. Install the retaining bolts (1,2) to the front bumper.

1. Tighten the bracket bolt (1) to 85 N.m (63 lb ft).

2. Tighten the bracket bolt (2) to 85 N.m (63 lb ft).

3. Tighten the brace bolt to 55 N.m (41 lb ft).

Image---4

5. Connect the electrical connector to the fog lamps, if equipped.

6. . Install the front grille.

Thank you for using FixYa.com

Regards, Lee Davidian