Volvo V7 '01 sunroof will not stop in closed position

Do you know how to do automotive electrical testing ?????? How to read a wiring diagrams ???? http://www.bbbind.com/free_tsb.html .Videos on youtube Ohms Law Tech Tip from L1 with Dave Hobbs Copy of Voltage Drop Essentials TST Motor Age The only way to find the problem , testing !

Sunroof Description and Operation (One Connector System)
Sunroof
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
• Open
• Vent
• Closed
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.

Your best bet , take it to a qualified repair shop or buick dealer .

Here's a description the sun roof
Power Sunroof System Components
The power sunroof system consists of the following components:
• Sunroof module
• Sunroof switch
• Sunroof motor, with 2 hall effect sensors and limit switch
• Sunroof window
• Sunroof sunshade panel
• Power supply for the sunroof module: RAP 25 A
• Ground G402

Override
The override function is used when needing to force a closing of the sunroof window. To override the system:
Turn ignition to ON.
Rotate the sunroof switch to the close position.
Press upward.
The sunroof switch data 6 circuit, or override circuit, will become grounded at the sunroof module. As long as the sunroof module sees this input, it will continue to slide the sunroof window to close, regardless of the other sunroof switch data circuits inputs.

I HAVE A Volvo v70 2005 Everything is dead on the passenger door. no centre lock or window actuvation. The bad part I cannot open the door ( I think when there is no electric to the door the ded bolt keeps the door locked. How to get the door open so I can take the trim panel off to see why there a problem

Do you know how to test automotive electrical circuit's with a DVOM - digital volt ohm meter ? When adjusting the moon roof did you see any switches ? sunroof limit switch
Measure the reference voltage of the sunroof limit switch soft stop signal circuit at the sunroof control harness connector to a good ground.
Does the reference voltage measure near the specified value?
4.5-5.5 V
Notice: Do not open the sunroof glass past the full open soft stop position. Doing so may damage the sunroof assembly and or the roof top.
Connect a jumper wire to the sunroof limit switch soft stop signal circuit at the sunroof control module harness to a good ground.
Turn ON the ignition, with the engine OFF.
Using the sunroof switch, operate the sunroof system, not to exceed the full open soft stop position.
Does the system operate as requested?

Do you know what a wiring diagram is ? Free one's here
http://www.bbbind.com/free_tsb.html Enter vehicle info. year ,make ,model an engine size . Under system click body & accessories ,then under subsystem click on sun roof . Click the search button then the blue link . See the control module , motor an the two switches ? One is probably miss adjusted . or bad !

Power Sunroof System Components
The power sunroof system consists of the following components:
• Sunroof control module
• Sunroof motor with the limit switches
• Sunroof switch
• Sunroof glass-spoiler type, with glass sliding above roof
• Sunshade
• Rail and track assembly upon which the sunroof glass rides
• Power sunroof system circuit breaker: PWR WDO 25 A
• Ground: G204

Sunroof Limit Switches
The sunroof limit switches track the position of the sunroof glass through two limit switches:
• Soft Stop limit switch through the sunroof limit switch soft stop signal circuit
• Vent Stop limit switch through the sunroof limit switch range signal circuit
The sunroof control module monitors the limit switches and based on the input combinations, determines the position of the sunroof glass. As a sunroof limit switch closes, the 5 volt reference will be shorted to the sunroof limit switch low reference circuit, pulling the 5 volt reference to 0 volts.
The sunroof control module monitors both sunroof switch input requests and based on the sunroof limit switch input combinations, will control an output to the sunroof motor, to drive the sunroof glass to the requested position.

Sunroof Motor
The sunroof has a bi-directional motor. When the motor is not operating both circuits are grounded. When the motor drives the sunroof glass in the direction from the closed to vent or vent to open position, the following occurs:
• Voltage is supplied to the sunroof motor open circuit.
• Ground is maintained to the sunroof motor close circuit.
When the motor drives the sunroof in the direction from the open to vent or vent to closed position, the following occurs:
• Voltage is supplied to the sunroof motor close circuit.
• Ground is maintained to the sunroof motor open circuit.
The sunroof control module is equipped with a timer circuit which stops the operation of the sunroof motor after 8 seconds.

there should be a slot you can put a flat head screwdriver in to turn the motor round and close the roof. the motor assembly there is a magnet inside and a reader to tell the motor when to stop or move. the sensor can fail and ope till it cannot move any more it also as a water trigger. this in the event that the vehicle is under water the sunroof opens so you can get out. this feature can go wrong a well.

Not familiar with the Volvo, but many cars (Toyota, Lexus, Acura, Honda, etc.) have drain holes at the corners of the sun roof assembly. These holes allow water that gets past the sunroof gasket to drain through tubes that carry the water to the bottom of the car, where it exits the car.

These drain holes are prone to clogging. If the Volvo setup is like those cars mentioned, you can see the front drain holes by opening the sunroof and looking closely at the two front corners of the assembly that holds the sunroof. I have used plastic weedeater line to open up these lines. Compressed air can also be used.

The problem is probably the 'flap' of metal that's popped up, just above the where the handle is.
The runners/rails have undoubtedly corroded, and now there isn't anything to pull it down.
Luckily, as a 'Get the roof shut cos it's p*^%g
down' solution,,.
You can just hold your finger on the flap, to hold it down, in between the sunroof, and hole as you shut it.
Just remember to remove your finger Before you finish closing the sunroof.
Happy motoring.

hold the switch down for around 20 seconds and it reset the sun roof /in close position

The sunroof continues to open and close normally from front to back, but the vent stays open.

Sunroof relay control module 99 seville