Where is the Engine control module

The Engine Control Module (ECM) on a 2001 Mitsubishi Airtrek is typically located in the engine compartment, near the battery. The exact location can vary depending on the specific model and engine type.
In general, the Engine Control Module (ECM) is usually located in one of the following places:

• On the driver's side, near the firewall
• On the passenger side, near the firewall
• On top of the engine, near the intake manifold

It's recommended that you consult your vehicle's service manual for the exact location of the Engine Control Module (ECM) in your car

P1296 CHRYSLER - 5 Volt Reference Voltage Missing At Throttle Position Sensor
https://www.autocodes.com/p1296_chrysler.html

Left side of Engine Compartment on 3.3/3.8L there is also ABS and others so make sure you get the right one. I believe the powertrain control module is near front by the battery.

unfortunately vehicle owners refer to vehicle parts using names that they make up as a dolacky or thingabob. If you can explain where this valve is located maybe some can help.

REMOVAL & INSTALLATION

Print

OPERATION

When the term Electronic Control Module (ECM) is used in this guide it will refer to the engine control computer regardless that it may be a Vehicle Control Module (VCM), Powertrain Control Module (PCM) or Engine Control Module (ECM).
The Electronic Control Module (ECM) is required to maintain the exhaust emissions at acceptable levels. The module is a small, solid state computer which receives signals from many sources and sensors; it uses these data to make judgments about operating conditions and then control output signals to the fuel and emission systems to match the current requirements.
Engines coupled to electronically controlled transmissions employ a Powertrain Control Module (PCM) or Vehicle Control Module (VCM) to oversee both engine and transmission operation. The integrated functions of engine and transmission control allow accurate gear selection and improved fuel economy.
In the event of an ECM failure, the system will default to a pre-programmed set of values. These are compromise values which allow the engine to operate, although at a reduced efficiency. This is variously known as the default, limp-in or back-up mode. Driveability is almost always affected when the ECM enters this mode.

REMOVAL & INSTALLATION

See Figures 1 and 2

Fig. Fig. 1: ECM mounting scheme-except 1996 models

Fig. Fig. 2: ECM mounting scheme-1996 models
The ECM is located in the passenger side footwell in the kick panel up to 1996. In 1996, the ECM is located in the engine compartment next to the battery.

1. Disconnect the negative battery cable.
2. Disengage the connectors from the ECM.
3. Remove the spring retainer off and over the rail of the ECM on vehicles except 1996.
4. Slide the ECM out of the bracket at an angle.
5. Remove the ECM.

To install:

1. Install the ECM into the bracket.
2. Install the spring retainer (except 1996) and plug in the electrical connectors.
3. Connect the negative battery cable.

The injector circuits include the Engine Control Module (ECM), the ECM relay, the injectors (either 4 or 6 of them depending on which engine your vehicle is equipped with) and all of the wiring, switches, and fuses that are related to these circuits including the ignition switch.

So, to put it simply, the injector circuit is located in the dash as well as all over the engine compartment.

Why are you looking for it?

some are mounted behind the right kick panel on passenger side, some are also mounted under the hood on one of the fender wells

For one i dont need your vin its a z24 which means it has a 2.4l engine it does not have an ECM it has a PCM powertrain control module, which is located for your car in the right rear corner topside of your engine bay, in 1995-2001 it is located inside the right front fender. I hope this info helps...

On this car the ignition timing is controled by Engine Control Module (ECM) and is not adjustable. However it can be inspeced using a scan tool.

Theres not enough information, sorry cant help you..