Removal of rear door panel to change power window motor

It is located behind the right rear quarter panel , In the back right of the interior !
Remove the right rear quarter trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side in Interior Trim.
Removal Procedure

1. Remove the rear seat. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
2. Remove the Third Pillar trim panel. Refer to Third Pillar Trim Replacement .
3. Remove the garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
4. Remove the door sill plate. Refer to Liftgate Door Sill Plate Replacement .
5. Remove the quarter panel trim screws.

A lot involved in this but not to difficult !

1. Remove the rear door sill trim plate. Refer to Front Side Door Sill Plate Replacement or to Rear Side Door Sill Plate Replacement .
2. Remove the lower rear seat belt cover and bolt.
3. Remove the trim panel from the vehicle.

Remove the sill plate. Firmly pull the sill plate up and out from the retainers.
Remove the sill plate from the vehicle. Start from the front of the door sill. Use a flat-bladed tool in order to pry the door sill plate.
Rear Side Door Sill Trim Plate Replacement
Use a flat-bladed tool in order to pry the door sill plate. Remove the sill plate from the vehicle.
Body Rear Corner Garnish Molding Replacement
Remove the rear upper garnish molding. Refer to Rear Upper Garnish Molding Replacement .
Pull down on the upper corners of the garnish molding in order to disengage the retaining clips. Pull in order to disengage the remaining retaining clips. Remove the rear corner garnish molding from the vehicle. Inspect the rear corner garnish molding for broken or missing retaining clips. Replace the retaining clips as needed.
Good Luck ! Fun job !!!!!

REMOVAL

1. Remove the watershield. (Refer to 23 - BODY/DOOR - FRONT/WATERSHIELD - REMOVAL)

2. Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent(FRONT DOOR GLASS CLIPS).

3. Disconnect wire connector from power window motor, if equipped.

4. Loosen screws attaching front and rear window guide rails to inner door panel (FRONT DOOR MANUAL WINDOW REGULATOR - TYPICAL).

5. Remove screw heads on guide rails from key hole slots in inner door panel.

6. Loosen screws attaching regulator to inner door panel.

7. Remove regulator from inner door panel.

8. Extract rear guide rail through inner door panel rear access hole (FRONT DOOR POWER WINDOW - TYPICAL).

9. Extract front guide rail through front access hole.

INSTALLATION

1. Insert front guide rail through front access hole.

2. Insert rear guide rail through rear access hole.

3. Place window regulator in position on inner door panel.

4. Place screw heads on guide rails in position through key hole slots in inner door panel.

5. Tighten screws to attach front and rear guide rails to inner door panel.

6. Connect wire connector into power window motor, if equipped.

7. Install door glass.

8. Verify door glass alignment and operation.

9. Install sound shield and door trim panel

DIAGRAMS CAN BE FOUND ON JUSTANSWER,COM

Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal

1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
   

1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
   

1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.
   
   
   Trim Panel
   
   
   
   
   
   Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole

1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
   

1. Remove two screws located at bottom of front door trim panel.
   

1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
   

1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
   

1. Pull front door trim panel from the top to release hooks from front door .
   

1. Remove front door trim panel.
   

Installation

1. Replace any bent or damaged fasteners.
   

1. Follow removal procedure in reverse order.
   

Body Side
Removal

1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
   

1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
   

1. Remove forward and rearward mating sections from under window trim.
   

Installation

1. Replace all christmas tree fasteners.
   

1. Follow removal procedure in reverse order.
   

1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.
   
   
   
   
   

Back
Removal

1. Disconnect rear window defroster wires.
   

1. Remove the liftgate window garnish moulding as described.
   

1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
   

1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
   

1. Remove liftgate trim.
   

Installation

1. Follow removal procedure in reverse order.
   
   
   Liftgate
   
   
   
   
   

1. Remove the door latch trim plate (coupe and sedan front doors).
2. Remove the ashtray (sedan rear doors).
3. Remove the seat belt retractor cover (coupe and sedan front doors). Use a suitable door trim panel removal tool to release the clip retainers
4. Remove the door lock trim plate and the power window switch, if so equipped.
5. Remove the window regulator handle by removing the inner retaining clip, if so equipped.
6. Remove the remote mirror control, if so equipped
7. Remove the trim panel retaining screws
8. Remove the door trim panel using a door trim panel removing to work loose the retainer clips.
9. Detach all electrical and remote mirror controls, as required.

To install:

10. Install the wiring harnesses through the openings in the panel, as equipped.
11. Position the trim panel to the door and align the clips. Press the trim panel to the door until all the clips are fully engaged. Align all the holes before engaging the clips.
12. Install the screws, remote mirror control and inside door handle bezel, as equipped.
13. Install the window regulator handle or power window switch.
14. Install the door trim plate, seat belt retractor cover or ashtray.

Very easy to do...I have a 1990 and they are interchangeable....88-94: Door Panel

1. Fully lower the door glass.
   
2. Remove the arm rest, door lock knob and inside door handle escutcheon.
   
3. For vehicles with manual windows, remove the regulator handle which is retained by a spring clip.
   
4. Gently pry the door panel away from the door.
   

Interior side and floor trim removal procedures-Pathfinder


Remove the lock button first before removing the door panel


Remove the plug to gain access to door panel retaining screws


Remove the trim cover


Remove the door handle trim


Remove the power window switch trim panel


After loosening the power window switch trim panel, disengage the electrical connection


Remove all the necessary trim panels before removing the door panel clips


View of the door panel retaining clip-clip must be installed in the hole straight


Make sure the watershield plastic is in place before installing the door panel

Installation is the reverse of removal.

Door Panels REMOVAL & INSTALLATION Continental 1995–00

1. Using a small screwdriver, remove the screw cover from the armrest of the front door trim panel.
2. Remove the two retaining screws.
3. Using the trim pad removing tool , remove the front door trim panel
4. Disconnect the electrical connectors.
5. Remove the front door window regulator switch housing. To install:
   
6. Position the front door trim panel on the door, align the two locators on the front door trim panel with the door and reverse the removal procedure.

Power Window Motor REMOVAL & INSTALLATION 1992–00 Vehicles

1. Disconnect the negative battery cable.
2. Remove the door trim panel and watershield.
3. Detach the motor wires at the multiple connector.
4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
5. Remove the motor from inside the door. To install:
   
6. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
7. Connect the power window motor wiring.
8. Connect the negative battery cable.
9. Check window operation.
10. Install the watershield and door trim panel

REMOVAL & INSTALLATION

1. Remove the window regulator handle with a pry tool or by removing the clip that retains it. This clip is tight and may be difficult to remove. To ease removal, make a tool out of an old wire hanger, take a length of the hanger and put a small hook shaped bend on the end. Use the tool to pull the clip off.
2. Remove the door handle trim plate.
3. On models equipped, remove the seat belt lap guide from the door panel.
4. Remove the screw from the arm rest pocket and carefully pry the pocket out. Remove the stereo speaker cover from the panel by prying out the beauty caps and unscrewing the phillips screws.
5. Pull the panel away from the door. The panel is retained by plastic clips, to ease removal use a trim removal tool (available at most auto parts stores). Try not to bend the panel to much when removing it or it will be damaged. On models equipped with power windows, disconnect the wiring from the switch before removing the panel completely.
6. Install the panel in position and reinstall all of the components removed. When positioning the panel, it will have to be pushed into place until the retaining clips catch.

Window Regulator, Rear Door, Explorer Removal

1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .

Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation

1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.

1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.

1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.

1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .

1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .

1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.

1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
   
   

1. If equipped with power windows, disconnect the wire from the regulator.

1. Remove the rear door window glass as described in this section.

1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.

1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
   

1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.

1. Remove two upper regulator attaching nuts.

1. Remove regulator from the front door (20125) .

Installation

1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.

1. Install regulator into access hole in inner panel.

1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).

1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).

1. Install two upper regulator attachment nuts.

1. Install door glass as outlined under Door Glass Installation.

1. Adjust glass as outlined under Adjustments .

1. Reconnect wire to regulator, if equipped.

1. Check operation of window regulator.

1. Install door watershield and trim panel. Refer to Section 01-05B .

SECTION 501-05: Interior Trim and Ornamentation 2000 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Rear Door Trim Panel Removal and Installation

1. Remove the rear door trim panel screws.

1. NOTE: The rear door trim panel has eight two-part pin-type retainers. The male part of the retainer will remain with the trim panel and the female part will remain with the door.
   NOTE: To release the door trim panel pin-type retainers, first pull outward on the bottom of the door trim panel.
   Remove the rear door trim panel.
   • Disconnect the window regulator control switch electrical connector.

1. To install, reverse the removal procedure.

This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal