Barina 2006 door trim removal

more than like if its just on door that wont look and the hoon sounds the door actuator will be faulty and you will need to replace the actuator.
To do this you will need pull the inside door handle off.
remove all door trim covers to access screw and disconnect mirror wiring.
remove all screws around door trim.
very carefully remove door trim once the trim is off you see a plastic inner door liner don't rip gently remove half .
look inside door and you will see the door actuator and lock,carefull lift up locking tabs so you can remove all door rods from actuator.
on the outside of door undo the 3 bolts and actuator will come out.
get the new actuator and fit it the same way the old one come out.
Before refitting the trim grab some silicon and reseal plastic to door to keep water out..

door control receiver part # 89741 or 89741B located in rear passenge pillar behind plastic trim or just below pillar in trunk behind carpeted trim held on by a screw wiring harness plugged into it.
fold down passenger rear seat very carefully remove plasic pillar trim and pull back carpeting find wiring and follow up or down and unplug receiver and remove retaining screw and match numbers to make sure you have correct part and plug new in and install screw and check operation then put everything back as you found it.

1 Prise out the trim cap and undo the screw securing the exterior mirror inner trim panel of door
2 Where a manually-adjustable exterior mirror is fitted, prise the rubber cover off the adjustment lever, then unscrew and remove the locking collar using pointed-nose pliers.
3 Pull the panel from its location to disengage the retaining clips. Disconnect the loudspeaker wiring connector and remove the panel.
4 Lift off the trim caps, undo the retaining screws, then remove the door interior handle surround.
5 Carefully prise off the loudspeaker grille then undo the three loudspeaker retaining screws. Withdraw the speaker from the door and disconnect the wiring connectors.
6 Undo the three retaining screws in the loudspeaker aperture, and the single screw in the oddments pocket just below the aperture.
7 Lift out the loudspeaker protective cover and withdraw the loudspeaker wiring from the base of the cover.
8 Prise out the trim cap and undo the screw securing the rear of the trim panel to the door frame of Fiat Punto car.
9 Undo the screw at the upper front corner of the panel, and the remaining four screws securing the lower edge of the panel to the door frame.
10 Using a suitable forked tool inserted between the door and the trim panel of Fiat Punto, release the press-stud clips located around the edge of the panel, then lift the trim panel upward.
11 Pull the panel from the door, noting that the lower window aperture weatherstrip is integral with the trim panel and must be released from tie door as the panel is withdrawn.
12 If work is to be carried out on the door internal components, it will be necessary to remove the plastic sealing sheet from the inside of the door. Start at one comer of the sheet and carefully peel it away, using a sharp blade to split the sealant bead, if necessary.
13 Store the detached sealing sheet such that it cannot become contaminated with dust; this will allow it to be re-used later.
Source (with illustrations) - Door inner trim panel removal and refitting FIAT Punto

In the lift gate inside trim panel you will see a plastic cap plug at the door latch area. Remove the plug to gain access to the latch.You will see the plastic plug cap at the bottom of the inside lift gate trim panel. ----------- Click this link below for more details:--- http://technoanswers.blogspot.com/2011/07/how-to-remove-tailgate-strut-on.html --------- This should help.Thanks.Helpmech.

check your armrest on the door panel, it should have 2 or 3 plastic plugs that cover the screws that hold the armrest onto the door,
these plugs can be gently levered out with a pointed instrument or a small screwdriver, also check for screws where you put your fingers to close the door when you are in the car.
if the door handle is on the armrest or the door trim you will see a x screw that holds it to the door, remove the screw
you may need to buy a set of torx drivers for removing the screws for the armrest and the door handle (Maybe)
once these are removed check for any screws around the bottom of the door trim, if there isnt any, use a flat instrument such as a knife blade or a blade screwdriver and put it between the back of the trim and the door and lever it back gently

Door Panels - REMOVAL & INSTALLATION

The many different design interiors make it impossible to list each fastener location. The trim panels that must be removed are held in place by screws and clips. These locations vary from model to model. After removal of all the fasteners that you are aware of, if the trim panel is still firmly attached, you probably missed a hidden fastener. If this happens, gently and carefully pry the area looking for the location that doesn't flex. The location that does flex is where you'll find the fastener(s) you missed. Screws and retainers are usually hidden. Handle trim, reflectors, light lenses and other plastic pieces usually cover the main retaining screws. Take great care with the plastic trim panels. Plastic trim panels are usually very hard plastic and extremely easy to crack. The following steps can be used to guide you through the removal and installation of the trim panels, but you may need to alter these steps to your specific needs.

1. Disconnect the negative battery cable.
2. Pull the inside door handle to the open position, unfasten the screw and remove the handle escutcheon.
3. If equipped with manual locks, remove door inside locking rod knob.
4. If equipped with manual windows, insert a suitable window regulator handle removal tool behind the handle. Disengage the retainer, then remove the handle.
5. If equipped with power windows and locks, use a small flat-bladed prytool to carefully pry the switch plate up, then detach the power component electrical connectors.
6. If equipped, remove the screws inserted through door armrest and pull handle assembly into door inner panel or armrest hanger support bracket.
7. Lift the seat belt trim panel up and remove the hidden retaining screws.
8. Remove the outside side view mirror trim plate retaining screw. Lift the panel up to disengage the retaining clip, then remove the trim panel from the door.
9. On styles with courtesy lamps located in the lower area of the trim panel, disconnect the wiring harness at the lamp assembly.
10. If equipped, use a suitable tool to pry the reflector plate from the side of the door panel.Remove bottom trim cover retaining screws, then remove the lower trim cover.
11. Remove any necessary electrical connector CPA clips, then unplug the electrical connectors.
12. On styles with integral armrests, remove the screws inserted through the pull cup into the armrest hanger support.
13. Unfasten the door trim panel retaining screws. The locations of the screws will vary depending upon the year of model of vehicle. The screws are usually hidden, so be sure to look carefully to make sure you don't miss any.After all of the trim panel retaining screws are removed, slide a suitable trim panel removal tool between the door panel and door perimeter to carefully disengage all of the trim panel retaining buttons. Make sure to position the tool close to the fastener, or the trim panel may be damaged.
14. Carefully lift the trim panel away from the door, checking to be sure all of the retaining buttons and screws and electrical connectors are unfastened.
    

To install:


Before installing the door trim panel, check that all trim retainers are securely installed to the panel and are not damaged. Replace damaged retainers as required.

1. Connect electrical components where present.
2. To install the door trim panel, pull door inside handle inward; then position the trim panel to the inner panel, inserting the door handle through the panel hole.
3. Position the trim panel to the door inner panel so that the trim retainers are aligned with the attaching holes in the panel, and tap the retainers into the holes with a clean rubber mallet. Install all previously removed items.
4. Install the remaining door panel components in the reverse order of removal.
5. After installation, connect the negative battery cable, then check for proper attachment and operation of electric components, if so equipped.
   

Hope helps (remember rated and comment this).

Front Door Panel - Town Car - Removal
CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove.

Snap out two door pull strap retaining screw covers. Remove screws.

Remove two screws on front and rear side of front door trim panel.
The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.

NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors.

Disconnect driver seat regulator control processor switch (driver door only) if equipped.
Twist out interior lamp wire assembly and remove the front door trim panel.
Installation

Ensure plastic watershield is secured to door panel.
Position front door trim panel to door. Connect interior lamp wiring.
Position the window regulator control switch housing and connect switch connectors. Install the retaining screws.
Connect driver seat regulator control processor (14C708) (driver door only) if equipped.
Align door lock side to its mating slide on the sheet metal (front doors only).
Snap in front door trim panel. Ensure all retainers fit properly.
Install two retaining screws on front and rear side of front door trim panel .
Install two retaining screws and pull strap covers.

Good luck Remember rated this).

on the inside of the door there should be a plastic cover the same shape as the unit that you can pry off (very slowly) and it may have some clips that you can pry off. when you remove the cover the three posts should be exposed and just remove the nuts and the rest is easy.................as far as your kid goes...........your on your own...........

Sure, you have to remove the outer blade by moving the plastic cover off of the mount location & then remove the nut. You'll need to remove the door trim panel once the back door is open, once removed you'll see the harness leading to the motor & the mounting bolts. once removed, it's a straight pull out & you are done. To remove the back door trim, you'll need to gently pry out the 2 lights with a padded flat screwdriver & disconnect the plug-in connector, push in on the little buttons at the bottom of the door and then pry the 1/2 " push in plugs out, (these are all reusable) remove the handle/grip by gently prying & the panel will more or less "pop" out of the holders. It's a push fit once the bottom retainers are removed. Good Luck

Both above answers are not right... I just replaced the Pass side power mirror assembly on my 97 Expedition. No heat, no directional.
The inside door panel must come off.
1. pry off interior triangular plastic trim piece inside of door at mirror area. Remove door panel screw at this area.
2. Pry off power window switch panel and remove door panel screw at this area.
3.Remove interior door light cover and remove screw at this area.
4. Remove plastic cover at door handle.
5. The interior door panel can now be lifted up to release it from it's fasteners.
6. Disconnect light and push power window switch assembly through the door panel and it can be set aside.
7. Disconnect mirror power at coupler.
8 Loosen three mirror mounting screws with 7/16 socket. DO NOT unscrew completely.. the will fall down the door cavity. Use a round magnet on holder to remove the screws completely.
9.Thread electrical connection into door panel and install mirror.
10. Smile when mirror works and drink a beer!
rayman