Need chart that shows figure numbers with jabsco part numbers for ultima lobe pump

Firebird App. Pontiac Part # Duration @ .050 Degrees Int/Exh Adv Duration Degrees Int/Exh Lobe Center Degrees Int/Exh Lobe Separation Angle Overlap Cam Lift Int/Exh Gross Lift Int/Exh
(1.5:1 Ratio Rocker) Gross Lift Int/Exh
(1.65:1 Ratio Rocker) 1977 TA6.6 549431 274/289 62 .249/.270 .374/.406 .411/.446 1978 TA6.6 10003402 273/289 54 .270/.271 .406/.407 .446/.448 1979 TA6.6 10003402 274/298 55 .249/.270 .374/.406 .411/.446 1967 400, 1968 350, 1973-76 400 w/ AT 9779066(E) OEM 200/210 273/282 106/116 111.25 55 .272/.271 .408/.407 .449/.448 1967-68 400HO w/ MT 9779067(P) OEM 200/213 273/289 113.5 54 .272/.271 .408/.407 .449/.448 1968 400 HO MT & RA-I AT, 1969 350 HO MT, 1969 400 MT, 1970
RA-III MT/AT, 1971-72 455 HO MT 9779068(S)
OEM 212/225 288/302 113/118 116 63 .272/.271 .408/.407 .449/.448 1967 RA MT/AT, 1968 RA-I MT,
(Some 1969 GTO RA-III MT) 9785744 (H)
OEM 224/236 301/313 112/119 115 76 .272/.271 .408/.407 .449/.448 1968-70 RA-II & RA-IV MT/AT 9794041
(T) OEM 230/240 308/320 112/115 114 87 .313/.313 .470/.470 .516/.516 (Stock in RAIV)

a misfire can be mechanical as well as electrical
code p 0300 is random/ multiple misfires detected
low fuel pressure is a probable cause from a problem fuel pressure regulator or problem EVAC system not venting properly causing a vacuum in the tank and starving the pump
erratic could be from valve problems on heating
loose valve seat insert/s, incorrect valve clearance from faulty hydraulic followers, cam shaft lobe failures are all part of the mechanical reason for random /multiple misfires

their are a multitude of places that deal with oem to reproduction parts their are also a lot of forums / and car clubs to pick their brains from this link has a lot of different interior parts for el caminos this is just to show what some of the shops are like and the other link is the break down for original codes for the 86 paint interior/exterior trim trim color ect
Interior Trim Accessories http://www.gbodycentral.com/forums/vins/1986-Malibu-ElCamino.php

Anon, Some older vehicles fuel pumps were driven using cam lobe or a attached Eccentric, egg shape collar. You may have wrong pump, lobe worn off, you could be missing a drive pin (this would allow further reach from lobe to pump arm). Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Fuel Pump Mechanical Type Demo
How Mechanical Fuel Pump Works
Revised How to Install Mechanical Fuel Pump on Chevy SB Short Version

Google for it, ask dealer for it, Possibly library repair manual.

get a Haynes repair manual,it should tell you everything you need to know

Your shop manual should show this. If you don't have one, parts stores sell these cheap.

Why replacing? Codes/ Check Engine Light on?

Printable View (263 KB) TSB
06-11-7

• 2001-2005 ESCAPE 3.0L UNSTABLE IDLE - 2001-2003 ESCAPE 3.0L AUTOMATIC TRANSAXLE SHUDDER - MEXICO ONLY

Publication Date: May 25, 2006
FORD: 2001-2005 Escape
ISSUE: Some 2001-2005 Escape vehicles equipped with a 3.0L engine may exhibit idle speeds outside the specified range. Some 2001-2003 Escape vehicles equipped with a 3.0L engine and CD4E automatic transaxle may exhibit a transmission shudder.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE

1. If the concern is a 2001-2005 Escape with idle speeds outside the specified range:
   1. Install a new idle air control (IAC) valve with jumper harness included in the kit. The new Denso brand IAC will be installed with the electrical connector facing the opposite direction of the original (Hitachi) valve which is why the jumper harness is required. The original (Hitachi) IAC connector faces the front of the vehicle while the new Denso IAC connector faces toward the rear of the vehicle.
   2. Referring to the calibration charts (Figures 1 and 2), select the applicable file and reprogram the powertrain control module (PCM) using the TSB Service Procedure and WDS/IDS release B40.5 and higher. Calibration files may also be obtained at www.motorcraft.com.
2. If the concern is a 2001 - 2003 Escape with transaxle shudder, drain, flush and refill the transmission fluid with MERCON® Multi-Purpose Automatic Transmission Fluid. Then, referring to the calibration charts (Figures 1 and 2), select the applicable file and reprogram the PCM using the TSB Service Procedure and WDS/IDS release B40.5 and higher. Calibration files may also be obtained at www.motorcraft.com.
3. When reprogramming the PCM use blank path programming. Select the proper file from the chart and manually enter the PCM part number or tear tag number to obtain the updated calibration file.

To Perform Blank Path Programming:

1. Connect WDS/IDS to vehicle.
2. Select "16 pin", select "All others, except those below", press TICK.
3. Screen shows installation of cable, press TICK.
4. Screen shows to turn ignition ON. DO NOT TURN IGNITION ON. Press TICK.
5. Screen shows progress bar, then screen tells you "No communication can be established with the PCM" and asks you if you want to retry? Select "NO". With the ignition key still OFF, press TICK.
6. Screen shows to turn ignition ON. Keep ignition in the "OFF" position, press TICK and you will be asked to cycle the key "ON" and "OFF" a few times. Please keep the key position in the "OFF" position through the key cycles.
7. Screen will show "The diagnostic tester is unable to communicate with this vehicle." You will be prompted to "select a vehicle from the vehicle list", press TICK.
8. A list of vehicles will be displayed, select ALL OTHERS, and press TICK.
9. Screen shows "To enable WDS to reprogram the PCM with the correct calibration", enter one of the following: Vehicle Calibration number (7 digits), Tear Tag number (4 digits), or PCM part number, press TICK.
10. Highlight the box next to the selection chosen, and enter ONLY ONE of the selections listed above. Press TICK.
11. Follow and answer correctly all remaining screens. Once PCM is reprogrammed communication should be reestablished and PATS system can be reset (if necessary) per Workshop Manual, Section 419-01.

PART NUMBER PART NAME 5L8Z-9F715-AA Idle Air Control Valve XT-2-QDX MERCON® Multi-Purpose Automatic Transmission Fluid
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage And Emissions Warranty Coverage
DEALER CODING BASIC PART NO. CONDITION CODE 9F715 42


Figure 1 - Article 06-11-7

P0204 is miss fire detected on #4 cylinder.

Below is TSB from VW on your problem...a common one.


Technical Product Literature Transaction No.: 2015153/1
MIL ON, DTC P0087, P1093 or P2293 Stored in ECM Fault Memory Release date: Jun 29, 2007
Condition
15 07 04 June 29, 2007 2015153
MIL ON, DTC P0087, P1093 or P2293 Stored in ECM Fault Memory
MIL ON with the following DTCs may be stored in ECM fault memory:
DTC Description
P0087 Fuel Rail / System Pressure - Too Low
P1093 Fuel Trim 2, Bank 1 Malfunction
P2293 Fuel Pressure Regulator 2 Performance

Technical Background
Excessive wear of intake camshaft lobe that drives the high pressure fuel pump. The wear limits maximum pump piston lift, causing fuel rail pressure fluctuations.
The wear on the camshaft lobe can also lead to wear on the base of the high pressure fuel pump cam follower.
Production Solution
Increase surface hardening of camshaft lobe for the high pressure fuel pump
Improved intake camshafts have Part No. 06F109101B.
Service

• Remove the high pressure fuel pump and visually inspect:
1. Base surface of the cam follower -6- in contact with the camshaft lobe.
2. Tip of the high pressure fuel pump plunger.
3. High pressure fuel pump camshaft lobe.

If the base of the cam shaft follower looks like -C- or -D-, no excessive wear is present.
Cam follower and camshaft should not be replaced.
If the cam follower base surface is excessively worn so that its surface is concave -B- or missing -A-, inspect the intake cam shaft lobe for wear.



If the high pressure fuel pump camshaft lobe shows excessive wear, replace the intake camshaft with Part No. 06F109101B and the cam follower with Part No. 06D109309C, see Group 15 Engine - Cylinder head, Valvetrain in ElsaWeb.

Inspect the tip of the high pressure fuel pump plunger for excessive wear.
If excessive wear is found the high pressure pump must also be replaced, see Group 20 Fuel supply in ElsaWeb.
Tip:
High pressure fuel pump plunger damage is only possible if the cam follower base has a hole in it and the plunger tip has come in direct contact with the camshaft lobe.
If no excessive wear can be found in the high pressure fuel pump cam follower or intake camshaft lobe, or if the damage is found in camshafts with part number 06F 109 101 B, create a Technical Assistance Contact Ticket under the Concern Type Engine and Engine Electronics in ElsaWeb.
Attach the complete diagnostic log to the contact, and call the VW Technical Assistance Center for further assistance.

Warranty
When procedure applies to vehicles within the New Vehicle Limited Warranty, use the following:
Claim Type: W2
Part Identifier: 1505
Damage Code: 1505 18 _ _ _* 2
Labor Operation:
2.0T FSI engine Use applicable SRT time in ElsaWeb
Diagnostic Time: Actual GFF time expenditure
Claim Comment: Input "As per Technical Bulletin 2015153" in comment section of Warranty Claim.

* Code per warranty vendor code policy.
Required Parts and Tools
Description Part No: Quantity
Intake Cam Shaft 06F109101B 1
Cam Follower 06D109309C 1

No Special Tools required.

you need two charts,actually. Haynes, if they make a book for it, shows the number and cross referenced to the fuse box, and then BMW manual will show what each fuse is for. It's rare for both pieces of info to be on one chart.