How to replace battery cable - 1994 GMC Suburban

How To Replace Battery Terminals - YouTube

? 6:50
https://www.youtube.com/watch?v=KU74feDrnAc
Sep 29, 2013 - Uploaded by TheDIYGuyDOTnet
A video on how to replace the battery terminals or cable ends on your car ... to do so and have before for a sub/amp install on my 04 Tiburon and ..... Battery Cable and Terminal Ends: Checking and Replacing - Duration: 4:19.

How to replace the battery on a Hyundai - YouTube

? 6:13
https://www.youtube.com/watch?v=DWlHE6ShvMI
Feb 6, 2014 - Uploaded by jimthecarguy
How To Replace The Battery On A 2008 Hyundai Santa fe. ... How to Install Replace Change Battery 2001-06 Hyundai Elantra - Duration: 4:01.Missing: refitting

2007 Tucson: How do I re-attach battery cable - CarGurus

if positive (red) cable, remove from battery, follow down cable and unhook any securing clips, remove the other end from starter. the ground cable will be attached to engine block, as well as body ground location near battery.

REPLACE BATTERY CABLES THE POSITIVE BATTERY CABLE COULD BE SHORTING TO GROUND.REPLACE STARTER SOLENOID IF NOT BEEN REPLACED.BESURE TO PLACE BACK FLEXIBLE CONDUIT THAT GOES AROUND POSITIVE BATTERY KEEP FROM SHORTING TO GROUND. LAST TIME I SEEN BATTERY CABLES OVER HEAT WAS EITHER STARTER AND SOLENOID SHORTING OUT OR VERY LOOSE BATTERY CABLES CONNECTIONS. REPLACE BATTERY CABLES IF THEY ARE MELTED HAVE STARTER CHECKED OUT YOU COULD HAVE FAULTY STARTER STILL.

REPLACE BATTERY CABLES.SOUND LIKE POOR GROUND AT BATTERY GROUND CABLE.IF BATTERY CABLES OLD AS VECHICLE REPLACE THEM.TURN OFF RADIO FIRST BEFORE REMOVING BATTERY CABLES.IF BATTERY CABLES OKAY.THE STARTER MOTOR COULD BE GOING BAD.

A simple way is to take another 12 volt battery and connect it with jumper cables right onto the existing battery connections. Connect positive + to positive and negative - to negative which is parallel wiring. Now remove the connections from the battery you are going to replace without knocking the connections from the donor battery loose. Once you get the new battery installed, simply disconnect the jumper cables. Make sure you connect the cables as described above to keep the voltage at 12 volts and do not connect them in series. Connect them wrong an you will have 24 volts and may damage your electronics. If for some reason you loose the code it is simple to get the code from Honda. Just go to the Honda Owners link below and register your Honda. You will need the VIN # off your car. They will provide the code free of charge.
https://www.ahm-ownerlink.com/login.asp?page=%2Fprod%5Fhome%2Easp

Hi, If the problem is associated to you replacing the battery, then it could be a few different things. 1) Is the replacment battery fully charged? If not, charge and retry. 2) Are the positive and negative battery cables connected correctly to the battery? With this you have to be sure that you have a good connection to each battery terminal. Try removing the cables and taking a wire brush to the terminals. Once clean, reconnect them and try to start again. 3) Is the positive cable broken? If broken replace the cable. 4) Is the negative battery cable broken or properly connected to the car? If broken, replace the cable. Good Luck!

Aftermarket parts houses have replacement battery cables for some cars. For other cars, there are replacement battery cable terminal ends available. You cut the existing terminal off of the battery cable and the replacement terminal will clamp on to the end of the cable with bolts.

NOTE: Nothing on your car works without the battery. I have had many vehicles towed into my shop because of improper cable end replacements. Make sure the connections are clean and tight and free of corrosion.

Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .
hope this helps . please rate my response.

A lot of cars have two cables on the positive post.
Do you need to replace the cables or is the battery post clamp broken. You can buy a replacement post clamp if you have the type of cables that are bolted to the clamp.
If you need the cable, a oem replacement from your dealer parts counter will match. You can get after market replacements, just look for one that matches your original as close as possible. The parts counter guy should be able to help.

You can cut off the end and replace it. The right ways is to replace cable. the first salution will get you by but will corroud after a while.