1993 Oldsmobile Cutlass Ciera Logo

Related Topics:

c
chris green Posted on May 28, 2017
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

93' cutlass ciera 3.3 wont stay on after turning over

Hello, I have a '93 Cutlass Ciera 3.3. I just got a brand new mass air flow sensor, a new battery and a new starter. the car turns over just fine but then cuts off shortly after idling. before the starter went out, i had to wait for the car to warm up a little before i could drive it and it would drive great even during the beginning of this winter. its still winter and rainy and snowy and the car wont stay on long enough to warm up even with all this new stuff in it. what is the deal!!??

1 Answer

Bill Boyd

Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

  • Oldsmobile Master 53,816 Answers
  • Posted on May 28, 2017
Bill Boyd
Oldsmobile Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

Joined: Jan 04, 2013
Answers
53816
Questions
7
Helped
11930810
Points
172802

Run the fault codes
not running indicates that the air/ fuel ratio is incorrect for the ambient temperature so you should be checking the ambient temp sensor /baro sensor and coolant temp sensor

5 Related Answers

Ronnie Wilson

  • 1596 Answers
  • Posted on Jul 15, 2009

SOURCE: 1991 Cutlass Ciera 3.3 low idle

Idle Control Solinoid Will Cause this with No Engine Light. = ICS

Ad
fingaz22

michael schultz

  • 1068 Answers
  • Posted on Oct 25, 2009

SOURCE: 92 Cutlass Ciera

if the lights light but don't blink you have a bad flasher if the don't light at all try you 4 way flashers and if they don't work you need a multi-function switch that controls brake light and blinkers and 4 way flashers.

let me know what you have and what you don't and i can better help diagnosis the problem with you.

Anonymous

  • 1 Answer
  • Posted on Jul 04, 2011

SOURCE: My Oldsmobile Cutlass Ciera with the 2.5 will not stay running

Nissan240sxe could you please contact me. I have the same problem and am about at my wits end trying to figure out whats wrong assuming you figured out the solution. Email me at [email protected] Thanks.

Anonymous

  • 1 Answer
  • Posted on Apr 30, 2012

SOURCE: would the mass air flow sensor make my 93 cutlass ciera c stall and then start later

that is possible pehaps you should check code jump aldl and read light for code dirty air filters can cause problems check harness connector also

Anonymous

  • 8 Answers
  • Posted on Nov 07, 2012

SOURCE: 1989 oldsmobile cutlass ciera car starts but won't stay running it sputters and backfires and dies

Hello dear

I have the same problem and i checked the knock sensor should give you a code 43!!! Disconect the connector of knock sensor and with multimeter you should get 4-6 volt with ground!!
Plsss contact me at [email protected] to disscus more about our problems !!

Regards

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

93 Cutlass Ciera issue keeping it running?

Disconnect your MASS AIR FLOW sensor connector and if car runs and does not quit then you found the problem .
Replace sensor and relay .
0helpful
1answer

'93 cutlass ciera 3.3 wont stay on after starting up

ignition module getting warm and cutting of or auto shutoff relay loosing power..
1helpful
1answer

Wont stay on

Sounds like your "Idle Air Control (IAC) valve is not working to raise RPM when engine is cold.

It is possible that the wires to the IAC were not reconnected when the MAF sensor was replaced.

It is also possible that another sensor, like engine temp sensor, was not reconnected after the work. Look carefully in the area around and under the MAF.

All else fails, the IAC is bad and needs to be replaced.
0helpful
1answer

Replace crank sensor in 89 olds cutlass calais

Scottykw I have an 88 Oldsmobile Cutlass Calais quad 4,2.3L needing help locating the knock sensor on my car,rough idling and slow and sluggish acceleration.ive replaced the crank shaft position sensor and spark plugs,and fuel filter and allot of other things, but not the knock sensor or the Mass air flow sensor...where can I locate the knock sensor?
0helpful
3answers

My 93 oldsmobile cutlass ciera stalls too much

Check the oil. Quite a few cars do that when they are low.
0helpful
1answer

Would the mass air flow sensor make my 93 cutlass ciera c stall and then start later

that is possible pehaps you should check code jump aldl and read light for code dirty air filters can cause problems check harness connector also
0helpful
1answer

Hi I have a 89 Cutlass Ciera and on my MAF SENSOR one of the bridge contacts has come loose. Can this be soldered or not? Thanks for your replies Dan

Hello danno44: My name is Roger and I will help you. I would recomend replacing the mass air flo sensor. Unless you have the correct soldier and soldier gun you will damage the sensor beyond repair. The sensor is a lot cheaper than they use to be. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger
6helpful
4answers

1988 Olds cutlass ciera trouble codes

I have a 1988 Oldsmobile Cutlass Ciera 3.8 ltr and for the life of me can't find out how to check the codes. I have looked and can't find the OBD1 plug in. I have been told I need to jump a and b something or another with a paper clip and read the lights on the dash. Can anybody fill me on how to do this. Thank you.
0helpful
1answer

Cutlass cierra stalling checked alternator no problem,tune up,new wires,oil change,pully,mas flow sensor still does the same but when i take off the maf senser it rides good ????

i was just dealing with the same problem check out your fuel injectors , fuel pump, ingnition module with coil overs and possible fuel filter mine was the pump injectors and module its also a 93 cutlass ciera 3.3 fuel inj. hope this helps
Not finding what you are looking for?

137 views

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...