Ok I have no money for you to give a answer so if can't help say sorry. ok I have high beams and fog lights .but no low beams but these lights are the type that stay on when you shout the car off for at least 3 to 4 mins or a little less whcould it be do I need to replace a fuse and if so where is the fuse box
Not a fuse problem , same fuse power's low an high beams . Looking at wiring diagrams an using a DVOM - digital volt ohm meter to test the electrical circuit's is the way to find the problem . The light's staying on for 3 or 4 min's. is a function of the BCM - body control module ! Do you know anything about automotive electrical testing ? Do you know what a wiring diagram is an how to read one . Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. Year , make , model an engine size . Under system click on lighting ,then under subsystem click on headlamps .Click the search button then the blue link. get yourself a cheap DVOM an test the electrical circuit's , this is how electrical problems are solved .
Electric Testing Techniques You Need to Know
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts
Plus reading factory service repair info for how it should work would be a good idea .
Headlamps
The headlamps may be turned on two different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the OFF position, for automatic lamp control (ALC). During ALC, the headlamps will be in day time running lamp (DRL) operation in daylight conditions, or low beam operation in low light conditions. The LH HDLPand RH HDLP fuses, supply battery positive voltage from the underhood junction block to the left and right headlamps. The circuit continues through both low and high beam lamps, then back to the underhood junction block. The low beam and high beam circuits continue to the headlamp switch. The low beam and high beam circuits also provide the body control module (BCM) with both low and high beam inputs. The headlamp switch includes the dimmer switch and the flash-to-pass switch. When the headlamp switch is placed in the HEADLAMP position a path to ground is provided. Ground is provided at G201. Depending on the position of the high/low beam switch, either the low or high beam circuit will now have power and ground.
The LH HDLP fuse in the underhood junction block, supplies battery positive voltage to the automatic lamp control (ALC) headlamp relay coil circuit. The ALC relay switch circuit is connected to the low beam circuit at the headlamp switch. When the headlamp switch is placed in the OFF position, the BCM will automatically turn on the low beams in low light conditions. The BCM energizes the ALC relay, closing the switch contacts and grounding the low beam circuit. Ground is provided at G201. With the headlights in the low beam position, the high beams may be momentarily turned on or flashed with the dimmer switch handle. The flash-to-pass feature is accomplished by pulling the dimmer switch handle toward the driver. The headlights may be switched to high beam with the opposite movement of the dimmer switch lever. When the headlamp dimmer switch handle is pulled toward the driver, the flash-to-pass switch closes grounding the high beam circuit. Ground is provided at G201. Both high beams will remain on until the driver releases the switch handle.
If the driver places the headlight switch in the HEADLAMP position , the headlights will remain on until turned off or the battery runs dead.
Do you know what a factory diagnostic trouble shooting chart is ?
Headlamps Inoperative - Low Beams
Step
Action
Yes
No
Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics
1
Did you perform the Lighting System Diagnostic System Check?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Lighting Systems
2
Place the headlamp switch in the HEADLAMP position.
Place the headlamp dimmer switch in the LOW position.
Do the low beam headlamps illuminate?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Disconnect the turn/headlamp wiper switch assembly connector C2.
Connect a 15 amp fused jumper between the headlamp low beam signal circuit and a good ground.
Do the low beam headlamps illuminate?
YES - Go to Step 4
NO - Go to Step 5
4
Inspect for poor connections at the harness connector of the turn/headlamp wiper switch assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 7
NO - Go to Step 6
5
Repair an open or high resistance in the headlamp low beam signal circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you complete the repair?
NO - Go to Step 7
--
6
Replace the turn/headlamp wiper switch assembly. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?
Go to Step 7
--
7
Operate the system in order to verify the repair.
Did you correct the condition?
YES - System OK
NO - Go to Step 3
SOURCE: low beam headlights not working on 2004 Pontiac Montana extended
You headlight lamp have a diffuser mechanism which allows it to flip between the hight beam and low beam feature of the bulb. In fact, you high beam will function even if the low beam is not working.
I would recommend the purchase of the new headlight lamp. It would cost you you any where from $15.00 per unit to get a replacement lamp
SOURCE: headlight trouble on sunfire 2003 with 2.2ecotech
sounds like either a wiring loom is shorting across somewhere ??where ----best of british to finding it
SOURCE: low beam headlight are not working. high beams and
The problem could be the headlamp switch.
You are right about the fuses.There is one for the LH high/low and one for the RH high/low.
Have you tried turning on the lamps manually with the switch?
SOURCE: i have no low beam headlights or daytime running
i had the same problem wit a 97 Sunfire GT. It was the light control switch on the steering whell column. i went to Advanced Auto for the part. I think it was around $35. The lights have worked perfect in all modes every since. hope this helps.
SOURCE: 2002 Pontiac Grand Prix GT headlights no power
clean the computer lead interface. my buddies car did the same thing, we cleaned the computer leads with a good eletronic spray cleaner and it fixed the problem.
216 views
Usually answered in minutes!
×