Why does my ford edge display "check compass module"?

It usually means the compass on the vehicle needs recalibrating. That is the thing that tells you are going north or wherever in the mirror. The module is in the back of the mirror. Resetting is usually very easy.

Find an empty car park.
Press the Compass button on the mirror.
Do 3 complete circles left.
Do 3 complete circles right.

Google

year make model manual

They are all online. Press CTRL+F and type in Compass,.

For optimum calibration, drive to an open, level location away from large metallic objects or structures such as bridges, steel buildings, etc. Disable aftermarket electronic accessories and switch off all non essential electrical accessories (heated rear window, heater fan, A/C, map lamps and wipers) and make sure all doors are closed. Start the vehicle. NOTE: The vehicle remains in the CAL mode until the compass has been successfully calibrated. NOTE: While holding the Front Controls Interface Module (FCIM) 7 and 9 buttons down, the compass display first enters the ZONE setting mode (after 5 seconds) and then after another 5 seconds (approximately 10 seconds total), the compass display enters the CAL mode. Press and hold (for approximately 10 seconds) the FCIM 7 and 9 buttons until the CAL indicator appears in the display, then release the buttons. NOTE: If the CAL indicator does not turn off after the vehicle is driven in a circle at least 5 times, repeat the procedure. Drive the vehicle slowly at less than 5 km/h (3 mph) in a continuous circle until the CAL indicator disappears from the display and the compass heading is shown. If the CAL message does not turn off after driving in a circle at least 5 times (and the procedure has been repeated at least once), install a new compass module (integral to the interior rear view mirror). For additional information, refer to Interior Rear View Mirror.

Electronic Compass The compass display and module are contained in the overhead console and are replaced as an assembly. For additional information, refer to Section 501-12 . The compass display can be turned off and on by pressing the MODE button in the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W, or NW.
Inspection and Verification
NOTE: Press the MODE button to turn on the display.

1. Verify the customer concern by operating the vehicle along roads of known direction to duplicate the customer concern with the compass.

1. Visually inspect for obvious signs of mechanical or electrical damage.

Visual Inspection Chart Mechanical Electrical

• Compass module

• Central junction box (CJB) fuse 15 (7.5A)
• Circuitry

1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

1. If the fault is not visually evident, determine the symptom and GO to Symptom Chart .

Pinpoint Test A: The Compass Is Inaccurate/Inoperative
Normal Operation The compass receives battery voltage from the central junction box (CJB) through circuit 964 (DB/LG). Ground for the compass is supplied through circuit 676 (PK/OG).

Possible Causes
• fuse
• circuit 676 (PK/OG) open
• circuit 964 (DB/LG) open or short to ground
• compass zone setting
• compass calibration
• compass module

PINPOINT TEST A: THE COMPASS IS INACCURATE/INOPERATIVE NOTE: Always set the zone and calibrate the compass before replacing an inaccurate compass.
NOTE: After installing a new compass, always set the zone and calibrate.
Test Step Result / Action to Take A1 CHECK THE OVERHEAD COMPASS DISPLAY

• Key in ON position.
• Check the overhead display.
• Does the overhead compass display remain on after prove out?

Yes
GO to A3 .

No
GO to A2 . A2 CHECK THE COMPASS MODE

• Press and release the SELECT switch on the overhead console.
• Does the overhead compass display turn on?

Yes
If the compass display turns on correctly, GO to A3 . If the compass display turns on, but the heading is inoperative/inaccurate or the display indicates VAR, GO to A4 . If the compass display turns on, but it does not display all directions, or indicates CAL, GO to A5 .

No
GO to A7 . A3 CHECK THE COMPASS DIMMING

• Turn the headlamp switch to the parking lamps ON position.
• Does the compass display dim?

Yes
TURN the headlamp switch to the OFF position. GO to A4 .

No
TURN the headlamp switch to the OFF position. GO to A8 . A4 CHECK THE COMPASS ZONE SETTING

• Set the compass to the correct zone for your location. Refer to Compass Zone Adjustment in this section.
• Does the zone adjustment set correctly?

Yes
GO to A5 .

No
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation. A5 CALIBRATE THE COMPASS

• Calibrate the compass. Refer to Compass Calibration in this section.
• Is the compass calibrated correctly?

Yes
GO to A6 .

No
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation. A6 CHECK THE COMPASS ACCURACY

• Position the vehicle at each of the 8 directions (N, NE, E, SE, S, SW, W, NW) and verify that the displayed heading is accurate. The vehicle must be stationary for at least 10 seconds at each direction.
• Is the compass display accurate in each direction?

Yes
The compass is OK. REVIEW the operation of the compass with the customer.

No
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation. A7 CHECK THE VOLTAGE SUPPLY TO THE OVERHEAD CONSOLE

• Key in OFF position.
• Disconnect: Overhead Console C930.
• Key in ON position.
• Measure the voltage between the overhead console C930-1, circuit 964 (DB/LG), harness side and ground.
• Is the voltage greater than 10 volts?

Yes
TURN the key to the OFF position. GO to A9 .

No
VERIFY the CJB fuse 15 (7.5A) is OK. If OK, REPAIR the circuit. TEST the system for normal operation. A8 CHECK THE DIMMING CIRCUIT

• Key in OFF position.
• Disconnect: Overhead Console C930.
• Turn the headlamp switch to the parking lamps ON position.
• Measure the voltage between the overhead console C930-4, circuit 484 (OG/BK), harness side and ground while rotating the instrument panel dimmer switch.
• Does the voltage vary between 0 and 10 volts?

Yes
GO to A9 .

No
REFER to Section 413-00 for further diagnosis of the instrument cluster and panel illumination. A9 CHECK CIRCUIT 676 (PK/OG) FOR OPEN

• Measure the resistance between the overhead console C930-2, circuit 676 (PK/OG), harness side and ground.
• Is the resistance less than 5 ohms?

Yes
INSTALL a new overhead console. REFER to Section 501-12 . TEST the system for normal operation.

No
REPAIR the circuit. TEST the system for normal operation.

The sensor for the compass is bad or unplugged

Hi Roger, I'm glad to help. Below is the procedure for resetting the compass on your vehicle.



COMPASS VARIATION ADJUSTMENT Compass variance, also known as magnetic declination, is the difference in angle between magnetic north and true geographic north. In some geographic locations, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this problem occurs, the compass variance setting may need to be changed.
To set the compass variance:

1. Using the Variance Settings map, find your geographic location and note the zone number Figure 1.
Figure 1 - Variance Settings 2. Turn the ignition switch to the On position. If the compass/thermometer data is not currently being displayed, momentarily depress and release the C/T push button to reach the compass/thermometer display. 3. On Electronic Vehicle Information Center (EVIC) and Compass Mini-Trip Computer (CMTC) equipped vehicles depress the Reset push button and hold the button down until "VAR = XX" appears in the display. This takes about five seconds. On Compass Temperature Module (CT) equipped vehicles depress the C/T push button and US/M push button down until "VAR = XX" appears in the display. This takes about five seconds. 4. Release the push button(s). "VAR =XX " will remain in the display. "XX" equals the current variance zone setting. 5. On Electronic Vehicle Information Center (EVIC) and Compass Mini-Trip Computer (CMTC) equipped vehicles momentarily depress and release the STEP button to step through the zone numbers, until the zone number for your geographic location appears in the display. On Compass Temperature Module (CT) equipped vehicles depress the US/M push button to step through the zone numbers, until the zone number for your geographic location appears in the display. 6. On Electronic Vehicle Information Center (EVIC) and Compass Mini-Trip Computer (CMTC) equipped vehicles momentarily depress and release the RESET push button to enter the displayed zone number into the EVIC/CMTC module memory. On Compass Temperature Module (CT) equipped vehicles depress the C/T push button to enter the displayed zone number into the electronic module memory. 7. Confirm that the correct directions are now indicated by the compass.

I would check all fuses and replace any blown and retest. If the compass is still not working..I would make sure there is power at the compass module...If there is.. I would replace the module.

Ford edge only has a compass not a outside temp display.

Copied from alldatadiy.com for 2002 Ford Truck Windstar V6-3.8L.....


Compass Calibration

1. Start the vehicle and locate the compass module mounted on the base of the mirror.

NOTE: For optimum calibration, drive to an open, level location away from large metallic objects or structures. Switch off all non-essential electrical accessories (rear window defrost, heater, A/C, map lamps, wipers, etc.) and make sure all doors are shut.

2. Press the RESET button until RESET to CAL is displayed in the message center display.

NOTE: To exit the calibration adjustment mode before carrying out a compass adjustment, turn the ignition switch to the OFF position.

3. Slowly drive the vehicle in a circle no more than five times at no more than 5 km/h (3 mph) until CIRCLE slowly changes to CALIBRATION COMPLETED in the message center display.

The module is likely loose or has a loose connection. On my 2006 Escape, it sits on the dash driver's side. I had something on my dash and when I made a turn....it slid accross the dash and hit the module. It knocked it out of place and displayed an Error on The Dash. Hope it helps.

overhead module with the temmp and compass typically just quit after a few years
pull it down and check voltage to the module