Question about 1994 Plymouth Acclaim

1 Answer

Broken fuel strap bolt how to repair - 1994 Plymouth Acclaim

Posted by on

  • richard steward
    richard steward Jan 12, 2014

    Hi richard steward, I want to help you with your problem, but I need more information from you. Can you please add details in the comment box?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 6,674 Answers

Use a self drilling bolt of close to same size and put beside location where broken bolt is, or drill hole beside or close to old one and install new bolt/nut/washer.

Posted on Jan 31, 2014

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove fuel tank on 95 Ford aerostar. It has a vapor leak we must repair a leak in vapor recovery system


Removal and Installation
  1. NOTE: Make sure fuel tank (9002) is properly supported during removal and installation procedures.
    Drain fuel from fuel tank .
  1. Loosen fuel tank filler pipe clamp.
  1. Remove fuel tank heat shield (9A032) from vehicle.
  1. Support fuel tank .
  1. Remove bolt from rear fuel tank support strap (9092) and remove rear fuel tank support strap .
  1. Remove bolt from front fuel tank support strap and remove front fuel tank support strap .
  1. Partially lower fuel tank to gain access and remove feed and return lines from sender ports. To disconnect push connect fittings, refer to Push Connect Fittings in this section.
  1. Remove electrical connector from sender unit.
  1. Remove fuel vapor hose from evaporative emission valve (9B593) .
  1. Lower fuel tank from vehicle.

Apr 04, 2017 | 1995 Ford Aerostar

4 Answers

Fuel leak


Probably the pipes are rottening all at the same time, have a complete replacement of all bad ones, also check the fuel pump.

Aug 04, 2008 | 2006 Chevrolet Silverado 3500

2 Answers

How do I remove the gas tank out of a 2006 Ford 500 no one knows


SECTION 310-01: Fuel Tank and Lines 2006 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION

All vehicles
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 .
  1. Release the fuel system pressure. For additional information, refer to Section 310-00 .
  1. Drain the fuel tank. For additional information, refer to Section 310-00 .
All wheel drive vehicles
  1. Remove the rear driveshaft. For additional information, refer to Section 205-00 .
All vehicles
  1. Remove the muffler. For additional information, refer to Section 309-00 .
  1. Disconnect the fuel vapor control tube assembly valve-to-fuel vapor tube quick connect coupling. For additional information, refer to Section 310-00 .
  1. Disconnect the fuel supply tube-to-fuel filter quick connect coupling. For additional information, refer to Section 310-00 .
  1. Disconnect the fuel vapor tube-to-fuel vapor control tube assembly valve quick connect coupling. For additional information, refer to Section 310-00 .
  1. Disconnect the fuel tank wiring harness electrical connector at the rear of the fuel tank.
  1. Release the clamp and remove the fuel tank filler hose from the fuel tank.
  1. Place a suitable lifting device under the fuel tank.
  1. Remove the 2 front fuel tank strap bolts.
    • To install, tighten to 35 Nm (26 lb-ft).
  1. NOTE: Do not bend the fuel tank straps.
    Loosen the 2 rear fuel tank strap bolts and position the 2 fuel tank straps aside.
  1. Lower the fuel tank enough to move forward, clear of the fuel straps then complete the lowering procedure.
  1. To install, reverse the removal procedure.

Procedure revision date: 08/19/2009


May 03, 2016 | Ford Cars & Trucks

1 Answer

Removal of steel fuel tank


there should be two straps holding the fuel tank in,they are bolted on one side remove the bolts and the straps should swing away from the tank besure to unplug any and all elect. connections,

Dec 24, 2012 | Cars & Trucks

2 Answers

Couldn't found the gas tank bolt


The tank has to have straps holding it on &
the straps have to have bolts or nuts

Dec 04, 2012 | 1988 Chrysler LeBaron

1 Answer

Were is the fuel filter location on this suv. I've look on the frame rails


if it is a 99-04 land rover here are the steps
FUEL FILTER
Service repair no - 19.25.02
Remove
1. Disconnect battery negative lead.
2. Depressurise fuel system. See this section.
3. Raise the vehicle.
WARNING: Support on safety stands.
4. Position container beneath fuel filter to catch spillage.
5. Disconnect fuel hoses from filter.
6. Remove 'O' rings and discard.
7. Remove bolt securing filter and strap assembly.

Remove assembly.

Refit
8. Transfer strap to new fuel filter.
9. Position filter and strap assembly to floor pan. Ensure that flow arrow points toward front of vehicle.
10. Secure filter strap with bolt.
11. Using new 'O' rings, connect fuel hoses to filter. Tighten to 20 Nm (15 lbf.ft)
12. Remove container beneath filter.
13. Remove safety stands. Lower vehicle.
14. Reconnect battery negative lead.

if you can provide me with an exact year and model i will be glad to help you. Thanks, Midwest-tek

Aug 31, 2010 | Land Rover Discovery Cars & Trucks

1 Answer

Need to take gas tank off does it just bolt to frame


Some vehicles used straps that bolted to the frame. Check to see if there are straps holding up the fuel tank. If so, usually one side of the strap is bolted on and the other sits inside a pivot point. If one side is bolted, just remove the bolts from the end of strap and the strap will swing out of place.

Jun 23, 2010 | 1990 Toyota Pickup

2 Answers

Muffler strap broken on 2001 saturn sc1 series how to repair the easy way


Part is a dealer only part. There is 2 pieces to it. The strap is all you should purchase. The other part disconnects via a treaded bolt through the rubber mount above the muffler. Loosen the bolt/clamp on the muffler first this will give you the room to reach above the muffler with good lighting.

Sep 11, 2009 | 1993 Saturn SC1

1 Answer

Starving for gas


check fuel filter first. rate as fixed if this helps.

Steel Midship, Aerostar
Removal and Installation
  1. NOTE: Make sure fuel tank (9002) is properly supported during removal and installation procedures.
    Drain fuel from fuel tank .
  1. Loosen fuel tank filler pipe clamp.
  1. Remove fuel tank heat shield (9A032) from vehicle.
  1. Support fuel tank .
  1. Remove bolt from rear fuel tank support strap (9092) and remove rear fuel tank support strap .
  1. Remove bolt from front fuel tank support strap and remove front fuel tank support strap .
  1. Partially lower fuel tank to gain access and remove feed and return lines from sender ports. To disconnect push connect fittings, refer to Push Connect Fittings in this section.
  1. Remove electrical connector from sender unit.
  1. Remove fuel vapor hose from evaporative emission valve (9B593) .
  1. Lower fuel tank from vehicle.

Apr 28, 2009 | 1995 Ford Aerostar

3 Answers

Fuel pump removal 96 nissan quest


Replace Fuel Pump for 1997 Nissan Quest

(1) If the fuel tank has more than one third full, you need to get the gasoline out. If it has one third or less full, you can leave it in the tank. However be very careful around the working area. Make sure you have read fire precautions in a general repair book. Take the fuel pump fuse out from the fuse box near the battery. Run starter for a few seconds. This will remove the fuel pressure in the gas lines. Disconnect battery at negative terminal. Jack up the rear of the van.

(2) Remove the fuel tank protector.
19add47.jpg

(3) Disconnect fuel pipes at the front end of the fuel tank. Use short pencils and extra rubber hoses to block disconnected pipes and hoses.
59aa089.jpg There are two pipes connected to the gasoline filler at the side of the van. Disconnect only the smaller one. The larger one is flex enough for the tank to be lowered.

(4) Disconnect the electrical from this connector. Jack the rear end of the fuel tank with a car jack and a piece of 2x4. Put the wood between the jack point and the tank. Then unbolt the two bolts showing in the picture.
128654f.jpg
(5) Lower the jack after the bolts are removed. The rear end of the tank should be lowered.
667f695.jpg

de57889.jpg

(6) Disconnect fuel lines on top of the fuel pump. Reconnect each short hose back to different pipes as shown in picture to block the pipes.
585888a.jpg
(7) Loose the six mounting bolts on the fuel pump assembly. The bolts should be loosen a little at a time in multiple turns. Also detach the electrical wire holders. After all bolts are removed, carefully take the assembly out of the tank.
dceea20.jpg

(8) Remove the fuel pump from the assembly as shown in picture. Then unplug the electrical wires. Note that two connectors are in different sizes, so that you will not be able to reconnect to a wrong terminal.
1310aad.jpg
(9) Put the new pump and new filter in. Reconnect the electrical wires. If necessary use a pair of pliers to make the connectors tighter. Make sure they are not loose. Reconnect gas inlet to the pressure regulator.
08db176.jpg
(10) Use a new O ring, put back the assembly to the fuel tank. Make sure the float of the fuel level senser is free, and the assembly is at the right orientation (as shown in picture). Screw back the 6 bolts after making sure the O ring is in right place. The bolts should be tightened in turns. Do not over tighten them. Then reconnect the fuel lines and make sure every fastener is tight. Put the electrical wire into holders.
90c2053.jpg
(11) Jack up the tank and put the two mounting bolt in. (see picture in step 4). Make sure they are tightened with specific torque. Reconnect the electrical connector.

(12) Reconnect two fuel lines at the front side of the tank. Refer to the picture in step 2. Reconnect the hose to the gasoline filler. Before you have a try start, double check if all fuel lines are securely connected and tightened.

(13) Start the engine. You need to crank more than a normal start because the lines were empty. The pressure is built up in some time.

(14) If engine starts ok, turn it off. Then check under the van if there is any leakage. If everything is fine put back the tank protector. (picture in step 2).

Mar 09, 2009 | 1996 Nissan Quest

Not finding what you are looking for?
1994 Plymouth Acclaim Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...