Question about 1995 Mercury Mystique

1 Answer

Replace front wheel baeringue

How do i remove and replace front rigth wheel bearing my self on a 1995 mercury mystique

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 45 Answers

It is a press in bearing . You will need about $600 in tools to get her done

Posted on Feb 06, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Tony Rodriguez

  • 255 Answers

SOURCE: Wheel Bearings

Hi, Front or rear???

Posted on Aug 17, 2008

Anonymous

  • 94 Answers

SOURCE: How do I remove and replace front wheel bearing on

you need to take the tie rod off , the lower ball joint off , take the strut bolt out and remove the nut and washer off the cv axel then pull the whole hub Assembly off then the new bearing need to be pressed in , then reinstall everything not as hard as it sounds

Posted on Mar 09, 2009

bob c

  • 752 Answers

SOURCE: how to remove and replace

Because of the extensive answer involved here you would be better off getting a Haynes manual on your car from www.autozone.com

Posted on Jun 01, 2011

Anonymous

SOURCE: how to replace wheel bearing

If you go to YOU TUBE, your can watch a movie
from in a repair shop, of it being done

All vehicle repairs, are only funky ,when you have no
knowledge of the task

Posted on Jun 12, 2011

adam spatola

  • 1 Answer

SOURCE: 1995 mercury mystique starter replacement process?

At first, it looks like an impossible task, however if you start by removing the positive battery cable, then unplug mass air flow sensor, carefully remove air filter box and its components from the throttle body. from there you should be able to see the starter better and have more room to work and get it out. You can take the battery right out if you want a little more working space for your elbows. take the wires off the solenoid, sometimes the old studs of solenoid will break due to corrosion. remove the two 13mm bolts that hold the startersome models have one at the bottom also that you will need to access from the bottom side.

Posted on Nov 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a 1998 mercury mystique, it needs front wheel bearing replaced, is there a video out there that can help ?


You'll need special tools to re seat the new races in the hub. The old races can be pushed out with a brass drift and a hammer. Same for the seal.

Sep 12, 2016 | 1998 Mercury Mystique

1 Answer

Replace front wheel bearing on 2000 mercury mystique


you will need a bearing press to change bearing or you can buy it as a compleat assembly below is a download of directions

Sep 25, 2014 | Cars & Trucks

1 Answer

Left front wheel


You may have a defective wheel bearing, it is not safe to drive have a shop look at it right away.

Nov 30, 2012 | 1995 Mercury Mystique

1 Answer

How to replace front wheel bearings in a 2000 Mercury Mystique?


Travis, this Mystique has sealed wheel bearings, you do not pack them with grease. You cannot even access the bearing. If you are not familiar with a car, you do not know if you are giving correct directions or not.

Feb 11, 2012 | 2000 Mercury Mystique

1 Answer

Does a 1996 mercury sable and 2001 ford taurus have the same engine


Its possible. In this time span Ford used two different motors, the overhead valve (OHV) Vulcan V6, and the Duratec 24V V6, which will bear the 24v DOHC badge on the front fender.

Aug 31, 2011 | 1995 Mercury Mystique

1 Answer

What is the torque spec on front wheel bearing on 1999 mercury mystique?


you need to seat the bearings with ~ 60lbs of torque while spinning the rotor. Then back off the nut 1 flat ..

Aug 26, 2010 | 1999 Mercury Mystique

1 Answer

How do you take off the front hub on a mercury mystique


the sindle has to be removed then the hub is pressed out and so is the bearing here is a picture.eb80942.gif

Jan 16, 2010 | 1999 Mercury Mystique

1 Answer

How do I remove and replace front wheel bearing on 1998 Mercury Mystique????


you need to take the tie rod off , the lower ball joint off , take the strut bolt out and remove the nut and washer off the cv axel then pull the whole hub Assembly off then the new bearing need to be pressed in , then reinstall everything not as hard as it sounds

Mar 09, 2009 | 1998 Mercury Mystique

1 Answer

Wheel Bearings


Hi, Front or rear???

Aug 02, 2008 | 1996 Mercury Mystique

1 Answer

1995 mercury mystique


you almost never need to reset timing. To do it, you remove a timing "jumper" block which disconnects the computer from the distributor. Then, you can check "base timing" with a timing light. It should be 10 degrees. Then, during computer self test, it should jump to 27 to 33 degrees. You need a "Star Tester" to do this part.

Jul 02, 2008 | 1995 Mercury Mystique

Not finding what you are looking for?
1995 Mercury Mystique Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...