Fault code B1A35 service keyless system - 2006 Chrysler 300

The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, a ssembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

Replace the receiver and or transponder. But they will have to be programmed to the car. Takes a scanner. Some garages can do it. Most times dealer.

Viper Keyless Entry Systems

https://www.viper.com/car/keylessentry/

Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ...

www.jcwhitney.com > Audio, Video & Electronics

20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCode™ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In · Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

You can buy a remote for this on ebay.

When the service engine soon light (Also called the check engine light or engine management light) is turned on this is to alert you to the fact that Powertrain Control Module (computer) has detected a failure somewhere in the systems it controls you may not feel any difference in the way the engine runs, this can be the transmission or the engine or emission system, there are fault codes set in the modules memory for these faults. What needs to happen now is to have the powertrain control module scanned with a special tool called an OBD2 electronic engine control scanner or a OBD2 code reader. Once the code(s) are read then you must perform the diagnostics for each code and make the appropriate repairs based on the findings of the diagnosis that was performed, this is called doing "Pinpoint" testing.

The contact brush may be grounding on something other than the horn button contact. The wires run up the steering column tube and may be damaged inside.

Alternately the relay or it's wiring may be at fault. Or if it occurs more often when it is wet, this Technical Service Bulletin likely applies

1998 Ford Escort Electrical System Service Bulletin 71979


Additionally if you have the keyless security system, there were at least one TSB issued that may be relevent.

1998 Ford Escort Electrical System Service Bulletin 148392

There are two multiplex control units - one on the driver side and one onthe passenger side - which one did you unplug? The one on the driver side is the main "Brain" while the other one is the one that houses the keyless reciever. According to the service manual, any troubleshooting of this system must begin with the one on the driver side. It can get quite involved because Honda does not provide actual troubleshooting (symptom) charts, just descriptions of the electrical connectors and what conditions should be present at each conector pin under what system condition. (each pin has to be tested to determine what is malfunctioning) The system is not capable of outputting fault codes of any kind.

I have the 1995-97 Lincoln Continental Alarm, Remote Starter, Keyless Entry Wiring, review it:




Hope helped.

This bulletin supersedes TSB# 02-90-001.
DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:

• 2001 - 2004 MY Elantra
• 2001 - 2004 MY Santa Fe
• 2002 - 2004 MY Sonata
• 2001 - 2004 MY XG300/350

NOTE

• The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
• The most current Keyless Adapter Cable Instructions are available in the following shop manuals:

SHOP MANUAL

PAGES

2004 MY Elantra
BE-73 - BE-74
2004 MY Santa Fe
BE-43 - BE-44
2004 MY Sonata
BE-40 - BE-41
2004 MY XG350
BE-46 - BE-47
KEYLESS ADAPTER CABLE INSTRUCTIONS:

1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable.
2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
   
3. Turn the Hi-Scan Pro ON
   and press ENTER
   . NOTE "Release date 29. Sep. 2003" OR LATER
   must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
   
4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
   and press ENTER
   .
5. Select vehicle model and press ENTER
   .
6. Select option "TRANSMITTER CODE SAVING"
   and press ENTER
   .
7. Ensure that the key has been removed from the ignition cylinder before proceeding.
8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
   
9. Press ESC
   on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
10. Turn the Hi-Scan Pro OFF
    and disconnect the adapter cable from the multi-purpose connector.