Location of the Purge Control Valve for 2003 Hyundai Tiburon

"Car won't go in reverse" - New Tiburon Forum : Hyundai Tiburon ...

www.newtiburon.com/forums/.../189049-car-won-t-go-reverse.html

Aug 8, 2010 - 23 posts - ‎16 authors
Okay guys I just sold my 03 tiburon GT 6 speed to a 16 year old. I just got a ... Join Date: Sep 2006. Location: ... "It stalls and just drift forward, no reverse lights" Now did he break somethng or is he putting it in 6th..... Any Ideas. ... To view links or images in signatures your post count must be 5 or greater. Location of reverse light switch? - New Tiburon Forum ...
8 posts
Jul 23, 2014
So who's reverse lights don't work? - New Tiburon ...
25 posts
Apr 11, 2009
More results from www.newtiburon.com
Missing: hatchback

2003 Hyundai Tiburon Manual Transmission Complaints

www.aboutautomobile.com/.../Hyundai/Tiburon/Manual+Transmission

My 2003 hyundai tiburon clutch and flywheel broke on 3 separate occasions since ...into reverse, I had a hard time finding it, it would not let me put it into reverse and I ....2006; Description of the Complaint: I have 2003 v6 tiburon, clutch failed at ... bought 2004 5 speed tiburon (she bought it before my problems started) and ...

Transmission Won't Shift/CEL Due to Failed Speed Sensors ...

repairpal.com > Problems > Hyundai > Sonata

replace the purge valve it self or the purge valve solenoid

All Hyundai engines are 'interferrence' engines, meaning valve clearance is less than '0' if valve timeing is off by more than 30 degrees.

Only 2 parts remaining are the thermostat and waterpump. Always start with the thermostat when diagnosing an overheating problem. If the car is overheating constantly under all conditions and coolant is backing up into the reservoir, it's very likely to be the thermostat. If it only overheats at low speed or idling, it's more likely the waterpump.

The correct "Hyundai" term for the valve that's attached to the Vapor Canister is the "Canister Control Valve".Why don't you try to clean the old one first. They get clogged with little bits of charcoal from the canister. It's simple so see if it's bad, take it off, and try to blow through the canister side with no electric going through. You shouldn't be able to blow because the valve is supposed to be closed. If you can blow it's because the valve is clogged and hanging open. If it is clogged, you might try and clean it.

Then take the hose off from the canister and clean the hose too, you'll get a handful of charcoal out before your done. If you don't clean the hose out, you'll probably clog the valve again, even if it's new.

That's why they usually change the canister and the valve at the same time. It gets clogged because you fill the tank to the max, it floods the canister with gas, and the charcoal floats up through the hose to the valve.

On your Tiburon the purge valve is located below the throttle body. It is easier to access if you remove the boot between the airbox and the throttle body. After removing the boot look under the throttle body, the purge valve will be found mounted in a rubber hangar and it has a vacuum hose to both ends.

This generally indicates a vaccumn leak, or sticking idle air control valve.

Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

this code refers to EVAP Emission Control System Incorrect Purge Flow, it can be tricky to diagnose because of the number of parts, I would first check the vacuum hoses between the purge valve and the air cleaner, then the purge valve and the canister, also check the fuel tank vent and fuel cap valve and gasket. any one of these can cause this check engine code. after checking this I would reset the computer and see if it comes back.