02 sensors bank 1 sensor 2

sensor 2 is always downstream of the Cat.

Which 02 sensor is bank 1 sensor 2? Bank 1 Sensor 1 is the first sensor closest to the engine. On Bank 1 means it is at the engine side with cylinders 1, 3, 5, 7, etc. Bank 1 Sensor 2 is the second sensor on the engine's exhaust pipe, usually behind the catalytic converter.
Jan 26, 2022

https://www.google.com/search?q=1996+acura+3.2+tl%2C+bank+1+sensor+2+location

..

The two manifolds are named "Bank 1" and "Bank 2", with "Bank 1" describing the manifold that is closer to the passenger compartment, and "Bank 2" describing the manifold that is closest to the front of the car. "Sensor 1" is located between the manifold and the catalytic converter, while "Sensor 2" is located between the catalytic converter and the joint of the y-pipe.

The bank that contains cylinder number one is bank 1. On your car bank one contains cylinders 1-3-5 and bank 2 contains cylinders 2-4-6. The 02 sensor before the CAT. is the Upstream sensor or Sensor 1. The sensor after the CAT. is the Downstream sensor or Sensor 2. Any questions please write back.

The 02 sensors are in the exhaust. In the picture you can see two 02 sensors in each bank, right and left. Before and after the cat. You trouble code may relate to bank one or bank 2 sensor. Sensor 1 or sensor 2.

Here's a link to your firing order,cylinder 1 is bank 1. Specifications Firing Order AutoZone com

did you replace to top intake gasket you removed when you replaced the back spark plugs ,and do you torque it down right

As of 1996,all cars sold in the US were required to have an OBD-II computer interface port.
You may want to go to Advance Auto Parts, AutoZone, or Pep Boys, and get a free read
of the code(s) that you computer may be posting to help with your diagnosis.

The code coming from your vehicle's computer may be one or more of:

P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)
P0131 02 Sensor Circuit Low Voltage (Bank I Sensor I)
P0132 02 Sensor Circuit High Voltage (Bank I Sensor 1)
P0133 02 Sensor Circuit Slow Response (Bank 1 Sensor 1)
P0134 02 Sensor Circuit No Activity Detected (Bank I Sensor 1)
P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 02 Sensor Circuit Malfunction (Bank I Sensor 2)
P0137 02 Sensor Circuit Low Voltage (Bank I Sensor 2)
P0138 02 Sensor Circuit High Voltage (Bank I Sensor 2)
P0139 02 Sensor Circuit Slow Response (Bank 1 Sensor 2)
P0140 02 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
P0141 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0142 02 Sensor Circuit Malfunction (Bank I Sensor 3)
P0143 02 Sensor Circuit Low Voltage (Bank I Sensor 3)
P0144 02 Sensor Circuit High Voltage (Bank I Sensor 3)
P0145 02 Sensor Circuit Slow Response (Bank 1 Sensor 3)
P0146 02 Sensor Circuit No Activity Detected (Bank I Sensor 3)
P0147 02 Sensor Heater Circuit Malfunction (Bank I Sensor 3)
P0150 02 Sensor Circuit Malfunction (Bank 2 Sensor I)
P0151 02 Sensor Circuit Low Voltage (Bank 2 Sensor I)
P0152 02 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0153 02 Sensor Circuit Slow Response (Bank 2 Sensor 1)
P0154 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
P0155 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0157 02 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
P0158 02 Sensor Circuit High Voltage (Bank 2 Sensor 2)
P0159 02 Sensor Circuit Slow Response (Bank 2 Sensor 2)
P0160 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0161 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0162 02 Sensor Circuit Malfunction (Bank 2 Sensor 3)
P0163 02 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
P0164 02 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0165 02 Sensor Circuit Slow Response (Bank 2 Sensor 3)
P0166 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
P0167 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)

Note: "Bank 1" is the side of the engine with cylinder 1. "Bank 2" is the other side.

P0300 - Random/Multiple Cylinder misfire detected
P0301 - Cylinder 1 misfire detected
P0302 - Cylinder 2 misfire detected
P0303 - Cylinder 3 misfire detected
P0304 - Cylinder 4 misfire detected
P0305 - Cylinder 5 misfire detected
P0306 - Cylinder 6 misfire detected
P0307 - Cylinder 7 misfire detected
P0308 - Cylinder 8 misfire detected
P0313 - Misfire detected with low fuel

Maximas with the VE30DE and VQ30DE engines use a distributorless ignition system that is controlled by the Engine Control Module (ECM). The ECM receives a signal from the crankshaft sensor (the CPS - Crankshaft Position Sensor), and processes the signal based on inputs
from other various engine sensors, including the Oxygen sensor.
(this is the role of the O2 sensor in ECM operation).
Then the ECM sends signals to each of the individual coils in the proper firing order.
This system is more efficient than a distributor, and has fewer moving parts. The high voltage coils are directly attached to each spark plug, allowing a higher energy spark within the cylinder. A high energy spark means a faster, more thorough burning of the air/fuel mixture, which produces more power and lower emissions.


SECONDARY SPARK TEST - works for all cars, including Maxima.


1. Remove the spark plug.

2. Install the spark plug to the ignition coil/coil pack, then attach the coil wiring.

3. Ground the plug at a good ground location on the engine.

4. Crank the engine and check for spark.

5. If spark occurs, the ignition system is functioning properly.

6. If no spark exists, test the ignition coil/coil pack, power transistor and related wiring.

----------------------------------------------------------------------------------------------------------------------------
HEI Ignition Spark test - works for all cars, including Maxima.

The next level test you may want to try is a HEI (high energy ignition) spark tester kit. Cost is
about $30 at most auto parts stores. Harbor Freight Tools sells a chinese equivalent for about $16.
Place the spark tester on each of the spark plugs, and watch as the little light in the tester will
light up each time the spark plug is fired by the computer. You can actually see weak or
intermittent sparking as the motor runs - you can tell by the relative strength of the light as
you compare the intensity and duration of the light across all 6 cylinders.

If your problem were the alternator (or its built-in voltage regulator), your battery would not be
getting a proper charge, and you
wouldn't be able to start the car after a drive, since the battery would have been drained during the
drive - normally, the alternator will both charge the battery and run all electrical
features of the car during a drive.

To test your alternator, place your DMM (digital multimeter) across the battery terminals while the
car is running - it should read 13.5VDC to 14.5VDC. With the car off, you can test your battery
voltage with the same DMM - it should read 12.65 VDC (for a fully charged battery).

Alternatively, you can take your car to Advance Auto Parts, AutoZone, or Pep Boys, and they'll
attach their "charging system tester" to your car and give your car a nice test for free.
I do this with my customers' cars just to get that nifty printout of the problem. Its nice
to show a vehicle owner somethng in black & white when I'm recommending a new charging
or ignition system component (some of which can be a bit pricey).

P0804 is the highest OBD-II trouble code.

Here's your Oxygen sensor codes.

P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)
P0131 02 Sensor Circuit Low Voltage (Bank I Sensor I)
P0132 02 Sensor Circuit High Voltage (Bank I Sensor 1)
P0133 02 Sensor Circuit Slow Response (Bank 1 Sensor 1)
P0134 02 Sensor Circuit No Activity Detected (Bank I Sensor 1)
P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 02 Sensor Circuit Malfunction (Bank I Sensor 2)
P0137 02 Sensor Circuit Low Voltage (Bank I Sensor 2)
P0138 02 Sensor Circuit High Voltage (Bank I Sensor 2)
P0139 02 Sensor Circuit Slow Response (Bank 1 Sensor 2)
P0140 02 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
P0141 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0142 02 Sensor Circuit Malfunction (Bank I Sensor 3)
P0143 02 Sensor Circuit Low Voltage (Bank I Sensor 3)
P0144 02 Sensor Circuit High Voltage (Bank I Sensor 3)
P0145 02 Sensor Circuit Slow Response (Bank 1 Sensor 3)
P0146 02 Sensor Circuit No Activity Detected (Bank I Sensor 3)
P0147 02 Sensor Heater Circuit Malfunction (Bank I Sensor 3)
P0150 02 Sensor Circuit Malfunction (Bank 2 Sensor I)
P0151 02 Sensor Circuit Low Voltage (Bank 2 Sensor I)
P0152 02 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0153 02 Sensor Circuit Slow Response (Bank 2 Sensor 1)
P0154 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
P0155 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0157 02 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
P0158 02 Sensor Circuit High Voltage (Bank 2 Sensor 2)
P0159 02 Sensor Circuit Slow Response (Bank 2 Sensor 2)
P0160 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0161 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0162 02 Sensor Circuit Malfunction (Bank 2 Sensor 3)
P0163 02 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
P0164 02 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0165 02 Sensor Circuit Slow Response (Bank 2 Sensor 3)
P0166 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
P0167 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)

Note: "Bank 1" is the side of the engine with cylinder 1. "Bank 2" is the other side.

near the exhaust manifolds, in the exhaust pipes,on both sides.

Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Hope helps (remember to rate this).