Question about 2003 Suzuki Aerio
Where is oil onion suzuki aerio 2003 standard
google translator fails again. sigh.
ask in english , if i try to respond , it say, do not use foreign words
how you did, i cant fathom.
Posted on Feb 25, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Funny you should mention that, I’ve been working on the same problem with my 04 Aerio for 2 days. If you've checked the bulb and that didn’t fix it then it's probably 1 of the 5 little resistors on the circuit board. They’re really small and aren’t soldered very well. Pull the clock and pop the white ABS cover off the back, once you remove the clock from the dash you won’t even need any tools to pop the rear cover. Now plug the clock back in (make sure you get the plug back in the right way or you’ll short everything out) then turn your key on and GENTLY push on each resistor with your finger while watching to see if the light flashes on. If it does then that’s the resistor with the bad connection. I say GENTLY because I wasn’t and the lose resistor popped off on mine and no matter how many times I try soldering it back on I cant get a good enough connection to make the light work.
If you do find the lose resister, use a small tipped medium heat soldering iron and fine electrical solder to carefully solder the ends of the resistor with a little solder as possible. What ever you do don’t knock the little thing off or you probably never find it again, and you probably never get it to make a connection again. I’d start with resistor 430, it’s the nearest of the 2 on the side of the plug-in pins on the circuit board. Hope you have better luck then I did…..
Posted on Jan 16, 2009
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls
Posted on Sep 23, 2009
Remove plastic gaurds on top of engine. On the head of the engine block. There are 4 black smaller rectangular boxes. They are each held down by a screw in the corner of each. Unplug the black box. Pull upward on it. The bottom of this tube is what connects to the top of the sparkplug. You will need a socket extension to get the spark plug socket that far down. When you connect with the spark plug it will seem like your shoving the socket so far down its going into the engine. Remove plugs then re assemble everything. Do one completly before going to the next as to not confuse the wiring order. I had to use medical forceps (very long medical tweezers) to get my plugs out they are in a deep shaft deep in the engine block itself. I tried needle-nose pliers and they did not go deep enough. Hope that helps.
Posted on Jul 21, 2010
Tips for a great answer:
Jul 04, 2014 | 2004 Suzuki Forenza
Feb 24, 2014 | 2003 Suzuki Aerio
Nov 10, 2017 | 2007 Nissan Sentra 2.0 SL Sedan
Jul 02, 2012 | 2005 Ford Explorer Eddie
Jun 18, 2012 | 2002 Suzuki Aerio
May 29, 2012 | 2004 Chevrolet Malibu Maxx
Feb 17, 2018 | Isuzu Rodeo Cars & Trucks
Jan 15, 2011 | 2001 Isuzu Rodeo
Apr 05, 2010 | 2000 Chevrolet Tracker
Oct 03, 2009 | 1998 Honda Passport
209 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: