Rough runs,dies alot,sputters,backfires,low rpgs,batter light while driveing,test showed random misfire code 03 chevy malibu
SOURCE: Rough idle, sputtering, and backfiring.
try turning ur idle up its the pin on the throtle body just make sure u tuen the engine off and on again fter each adjustment to reset ur computer on ur engine
SOURCE: 03 chevy express 6.0 misfire
P0300 Diagnostic Code - Random Misfire
Technical description:--
Random/Multiple Cylinder Misfire Detected:---
Exactly what does this code means:--
Basically this means that the the car's computer has detected that
not all of the engine's cylinders are firing properly.
A P0300 diagnostic code indicates a random or multiple misfire. If
the last digit is a number other than zero, it corresponds to the cylinder
number that is misfiring. A P0302 code, for example, would tell you cylinder
number two is misfiring. Unfortunately, a P0300 doesn't tell you specifically
which cylinder(s) is/are mis-firing, nor why.
Symptoms:--
the engine may be harder to start.the
engine may stumble / stumble, and/or hesitate.
other symptoms may
also be present…There may be rough idle,
sputters and stalls and jerks.
Causes:--
A code P0300 may mean that one or more of the
following has happened:
Faulty spark plugs or wires, Faulty coil (pack), Faulty oxygen sensor(s)
Faulty fuel injector(s),Burned exhaust valve, Faulty catalytic converter(s)
Stuck/blocked EGR
valve / passages, Faulty camshaft
position sensor, Defective computer.
Possible solutions for this error problem:--
If there are no symptoms, the simplest thing
to do is to reset the code and see if it comes back.
If there are symptoms such as the engine is
stumbling or hesitating, check all wiring and connectors that lead to the
cylinders (i.e. spark plugs). Depending on how long the ignition components
have been in the vehicle, it may be a good idea to replace them as part of your
regular maintenance schedule. I would suggest spark plugs, spark plug wires,
distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a.
coil packs). In some cases, the catalytic converter has gone bad. If you smell
rotten eggs in the exhaust, your cat converter needs to be replaced. I've also
heard in other cases the problems were faulty fuel injectors.
Random misfires that jump around from one
cylinder to another (read: P030x codes) also will set a P0300 code. The
underlying cause is often a lean fuel condition, which may be due to a vacuum
leak in the intake manifold or un-metered air getting past the airflow sensor,
or an EGR valve that is stuck open.
Thanks. Keep updated for any more query. You can rate this
solution and show your appreciation.
SOURCE: code reads "random/multiple cylinder misfire
Basically this means that the the car's computer has detected that not all of the engine's cylinders are firing properly.
A P0300 diagnostic code indicates a random or multiple misfire. If the last digit is a number other than zero, it corresponds to the cylinder number that is misfiring. A P0302 code, for example, would tell you cylinder number two is misfiring. Unfortunately, a P0300 doesn't tell you specifically which cylinder(s) is/are mis-firing, nor why.
Symptoms may include:
the engine may be harder to start
the engine may stumble / stumble, and/or hesitate
other symptoms may also be present
Causes: A code P0300 may mean that one or more of the following has happened:
Faulty spark plugs or wires
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector(s)
Burned exhaust valve
Faulty catalytic converter(s)
Stuck/blocked EGR valve / passages
Faulty camshaft position sensor
Defective computer
Possible Solutions:
If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.
If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.
Random misfires that jump around from one cylinder to another (read: P030x codes) also will set a P0300 code. The underlying cause is often a lean fuel condition, which may be due to a vacuum leak in the intake manifold or unmetered air getting past the airflow sensor, or an EGR valve that is stuck open.
Hope helps.
SOURCE: chevy malibu misfire
if all that is good then the only other two things it can be is a intake gasket or a head gasket
253 views
Usually answered in minutes!
×