Codes: co246, co252, co242, co251
SOURCE: abs code CO246, 2000 K3500 GMC w/7.4l , replaced
Here is some information that will help you, your code that is coming up or popping up is relating till the EBCM ground. Please Read below as some of this information might help you.
Some customers may comment that the ABS light is on. Upon further
inspection, DTCs C0265 and C0201 may be set in the brake module. It is
also possible for DTC U1041 to set in other modules. There may also be a
loss of communication with the brake module.
Cause
A poor connection at the EBCM ground is causing unnecessary replacements of brake modules.
Important: The EBCM Ground is different for each application. Refer to the list below for the proper ground reference:
• Midsize Utilities = Ground 304
• SSR = Ground 400
• Fullsize Trucks and Utilities = Ground 110
Correction
DO NOT REPLACE THE BRAKE MODULE.
Perform the following steps to improve the connection of the EBCM Ground:
Remove
the EBCM Ground. The EBCM Ground is located on the frame beneath the
driver's side door. If multiple grounds are found in this location, the
EBCM ground can be identified as the heavy (12-gauge) wire.
Clean the area, front and back, using a Whiz Wheel®.
Install the ground, then the washer and then the bolt to the frame.
Important:
It is important to use the bolts, washers and nuts specified in this
bulletin. These parts have been identified due to their conductive
finish.
Install a washer and nut to the back side of the frame.
Tighten
Tighten the nut to 9 N·m (79 lb in).
Cover the front and back side of the repair area using Rubberized Undercoating.
An
additional check can be made to ensure a good connection for the
Battery Cable to Frame ground. It is possible for this ground to cause
similar symptoms with the ABS as described above.
Parts Information
FULL-SIZE TRUCKS, SUVs AND H2
Part Number
Description
11588564
Bolt
15650962
Washer
15672934
Nut
12378398
(in Canada, 10952414)
Rubberized Undercoating -- Paintable
MIDSIZE SUVs
Part Number
Description
11517555
Bolt
15650961
Washer
11503749
Nut
I hope this helps for you, MIke
Check
engine light comes on and off, these are indication that there is some
error code stored in your vehicles ECM. The engine module computer
needs to be scanned. These will give the code and as per the error code the
further problem can be detected and confirmed. The engine light
indicator blinks or remains steady on dash when engine computer
noticed any problem with any engine electrically operated components.
For
more help, I suggest you to refer the help links provided below. These will let
you know more about which areas to look, check, when there is engine light
coming up on dash panel.
---------
Click
the link below: -------
http://whoisbyme.blogspot.in/2012/06/malfunction-indicator-light-on.html
---------
http://howtobyme.blogspot.in/2012/02/check-power-train-message-with-orange.html
-----------
http://whatisbyme.blogspot.in/2012/05/2007-toyota-highlander-hybrid-yellow.html
-----------
------------
http://whatisbyme.blogspot.in/2012/05/car-runs-fine-but-check-engine-light-is.html
----------
http://howtobyme.blogspot.in/2012/01/check-engine-light-with-codes-p2195-and.html
----------
http://schematicsdiagram.blogspot.com/2011/12/how-to-read-codes-from-check-engine.html
----------
http://schematicsdiagram.blogspot.com/2011/12/vehicle-smog-test-failed-due-to-no.html
http://schematicsdiagram.blogspot.in/2012/02/obd-code-is-cleared-but-check-engine.html
-------------
http://schematicsdiagram.blogspot.com/2011/12/car-jerks-while-going-uphill-and-check.html
-----------------
http://schematicsdiagram.blogspot.in/2012/02/toyota-camry-check-engine-light-flashes.html
-------
These
details will help.
Thanks.
96 views
Usually answered in minutes!
×