Question about 2005 Ford Excursion

1 Answer

Ford Excurtion will start normal, but stall when putting in gear (reverse) or braking. When re-starting it runns ok until next braking.

The car usually runs ok when cold. after about 30 min driving, it will stall with battery light and "check engine" light on. When I put it in park and then re-start, it will run again. It will stall when putting it into drive or reverse unless I press the brake and give gas (about 2000 rpm). then it will run until I have to stop then the same problem again.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Ford Master
  • 1,249 Answers

Have the catalytic converter checked at your local muffler shop...clogged...worn out...Hope this helps.

Posted on Mar 12, 2014

Ad

4 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Mark Babineau

  • 1129 Answers

SOURCE: after driving for 15 minutes truck stalls,restarts

put a OBD II code reader on it see if it has stored any codes if not replace the TPS sensor and the MAF sensor do the replacements at different times so you don't buy one or the other for nothing

Posted on Jul 03, 2009

Ted Schore

  • 7353 Answers

SOURCE: car keeps stalling when brakes applied, then starts but turns off

I dont know why, but one time my truck was low on trans fluid and after I topped it off, it didnt stall anymore when put into gear. as fro the odometer i dont know, it may have to go out completely before any diagnosis can be done.

Posted on Oct 13, 2009

Testimonial: "I will do that, but the other day we realized it only does it when one of us changes the steering wheel position...somehow the wires may be pinching?"

dncholas

dncholas

  • 222 Answers

SOURCE: 1990 Ford Probe 2.2 automatic stalls in forward, reverse OK

Sounds like a bad IAC (idle air control valve/sensor) that controls your idle when going from throttle to idle. If bad your idle will act crazy and can cause stalls easily. Pretty sure that's it.

Posted on Aug 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 jeep liberty won't move when put in gear (like brakes are locked).crank it in neutral put in gear it will go till i touch brakes then won't move again.WHAT'S WRONG WITH THIS THING.


gear, is this a Manual trans? or AUTO you said gear.
what gear, please name the gear, 1,2,3,4,5 R
or PRNDL ( a/t box auto matic) what shift lever selection?
what is out door air temp, you do know brakes can get wet and freeze right?
it wont go you meant? until brakes are touched, key word won't?

ok engine only starts in PRNDL set to N??
is that it?
and then when you shift to D, the car will not move
what about the other gears.? try them all yet?

my guess (wild) is that you dont know how park lock out works.?
that you must hold the brake pedal down to shift to park or neutral.
is that it? (read operators guide?)

my guess is car is not drive-able. key point1 (a dead car)
point 2, engine starts and runs. and races on demand with gas foot.
point 3, im lost. (no trans stated or clear symptoms.)

my jeep has 6speed manual box
and the clutch allows me to start car.
on Automatics trans must be in park or neutral to crank engine.

"it will go till i touch brakes"



I read that 10 times,
my 2nd guess. the engine stalls ?

IS THAT IT, stalls means engine RPM is 0
and right foot actions are dead.
and all dash lamps glow, telling you STALL is now.

Feb 26, 2015 | 2004 Jeep Liberty

1 Answer

Kia Rio 2005 manual, the gear will get stuck and car shakes and stalls on its own when I come to a stop, foot on clutch and brake, in reverse and first gear.


what would happen if you put it in first gear,put your foot on the clutch then try to start the car....of course pick a place where safe!!!...if it rolls forward while cranking ,the clutch plate is touching the flywheel (in other words the clutch all the way down while in gear while cranking,should NOT touch the flywheel(transmission part that makes the car move) so if it moves then it shows the transmission reacts to the clutch touching the other jiggamathig. Possibly clutch system needs bleeding (air in the hydraulic system). I'm sure your car has this thing called a "clutch slave cylinder". Now,this is one thing I would check first.

Dec 21, 2013 | 2005 Kia Rio

1 Answer

1995 grand am se 2.3L. starts idles, runs good. stalled while coasting to stop. started right away fine, idles and runs good and smooth, but dies when put in reverse or drive. after towing it home. after...


the question is-- was you foot on the brake at home or was just the hand brake applied
when driving , slowing , stopping standing , all have the foot on the brake which is activating a brake booster and if that is faulty , the vacuum leak causes the problem

Nov 23, 2017 | 1995 Pontiac Grand Am

1 Answer

Galant vrg-gdi-when i engage reverse the car stalls--but once you start moving --ok


You vehicle uses a Idle air control motor,(IAC) when you put a load on the vehicle (Drive or reverse) the ECM detects the load and idles up the IAC, even for the A/C (air conditioner) You can try a throttle body cleaning. or a new IAC

Mar 01, 2012 | Cars & Trucks

2 Answers

As you've probably heard before my 91 cav starts fine gets warm stalls at lights starts right back up but cuts off when i put it in gear


pull off the transmission transition switch wire pluged on to tranny
start car drive should be fine never hook op again 0 money
or pay 700 dollars to install a new one
or buy switch pull tranny and install your self

Jul 14, 2010 | 1991 Chevrolet Cavalier

1 Answer

Car keeps stalling when brakes applied, then starts but turns off


I dont know why, but one time my truck was low on trans fluid and after I topped it off, it didnt stall anymore when put into gear. as fro the odometer i dont know, it may have to go out completely before any diagnosis can be done.

Oct 13, 2009 | 2001 Ford F150 Styleside SuperCrew

2 Answers

My daughter has an 2000 ford excurtion. when she puts into park it will drift forward or backwards depending on the grade. What should I look for


http://forusa.40host.com/about-au5a/index.html autum
http://allforall.40host.com/hallowee3b/atend.html halloween. s
http://allforall.40host.com/hallowee3b/quscche.html halloween witch


Aug 26, 2009 | 2000 Ford Excursion

1 Answer

Car stalls when i put it in drive or reverse,


Sounds like your vacuum assist brakes diaghram has sprung a leak. Pull the hose to the assist and plug it with a bolt or something. Then try it.

May 20, 2009 | 1997 Volvo 850

2 Answers

2000 crown victoria -brake lites failed


You have a bad switch at the brake pedal. Or a loose wire. Try light pulling on the wires on the switch at the brake pedal under the dash. They should be tight and secure. If tight and secure the switch could be bad.

Jul 03, 2008 | 2000 Ford Crown Victoria

Not finding what you are looking for?
2005 Ford Excursion Logo

512 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...