Question about 1999 Jeep Wrangler

1 Answer

Replace ignition switch on 99 jeep wrangler - 1999 Jeep Wrangler

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Jeep Master
  • 443 Answers

The ignition key must be in the key cylinder for cylinder removal. The key cylinder must be removed first before removing ignition switch.REMOVAL 1. Disconnect negative battery cable at battery. 2. If equipped with an automatic transmission, place shifter in PARK position. 3. Rotate key to ON position.4. A release tang is located on bottom of key cylinder.5. Position a small screwdriver or pin punch into tang access hole on bottom of steering column lower cover.INSTALLATION 1. If equipped with an automatic transmission, place shifter in PARK position. 2. Position key cylinder into steering column as it would normally be in the ON position. 3. Press key cylinder into column until it snaps into position. 4. Check mechanical operation of switch. Automatic Transmission: Be sure transmission lever is locked in PARK position after key removal. If key is difficult to rotate or is difficult to remove, the shift lever-to-steering column cable may be out of adjustment or defective. If key can be removed, release lever mechanism may be defective. Release lever mechanism is not serviced separately. If repair is necessary, the steering column must be replaced. 5. Connect negative cable to battery. 6. Check electrical operation of switch. Replace ignition switch on 99 jeep wrangler - ab7076e7-9719-44a3-b66a-8584c6b2a3c1.jpg

Posted on Apr 09, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Richard Scordino

  • 6982 Answers

SOURCE: 1988 Wrangler Ignition Switch Removal

There are four (sometimes two) bolts that hold the steering column to the dash. remove them & column will come down to let you get in there.
follow instruction sheet with switch. if you don't get it centered correctly it wont work correctly.

Posted on Jan 05, 2009

Richard Scordino

  • 6982 Answers

SOURCE: replace 1995 jeep wrangler catalytic converter

If it has flanges on both ends, just unbolt it and replace. If it has welded pipes you will need to cut it off and use adapter sleeves and clamps. Really not rocket science...at worst, you may need to remove the hangars on the rear portion of the system to get enough room to install.

Posted on Jun 17, 2009

Richard Scordino

  • 6982 Answers

SOURCE: 2006 Jeep Wrangler won't start

First, make sure you can turn the engine by hand. If you can't then the starter can't turn it either. Have someone else turn the key and look for the source of the click...may be a relay. Go over the starting circuit with a volt meter. Check for power at the starter main terminal and then with the key turned to "start" check for power at the trigger terminal on the starter. Check battery voltage and check relay operation.
You have a neutral safety switch on the transmission if its an automatic and a clutch switch if it's a stick. Check them as well. Make sure battery grounding on fender and block are also clean and secure.

Posted on Oct 02, 2009

Testimonial: "Will try! Thanks!"

jonesspammai

  • 553 Answers

SOURCE: 2000 jeep wrangler will not start from the key

It sounds like you have a bad neutral safety switch or your linkage is worn enough that it's not registering properly.

Posted on Jun 07, 2010

liltsar

  • 1 Answer

SOURCE: need to no how to replace ignition switch in 1993

www.eppiccomputer.com/dale/jeepjunk/tilt/tilt.html

This should give you an idea.

Posted on Jul 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace ignition switch on 1997 jeep wangler


Wells Jeep/Chrysler Ignition Switch Replacement LS711 LS922 ...

https://www.youtube.com > watch

I had the same problem but I just went to where I bought my car and they fixed it . Here's a way you can do it yourself if you can:)

Jun 20, 2014 | 1997 Jeep Wrangler

1 Answer

I have a 1999 Jeep TJ, the wipers, radio and turn signals all stopped working. Checked fuses, nothing seems blown. Also, they all work when the ignition switch is in the accessories position, but when...


Had the same thing with my 2004 Wrangler. The Airbag light stayed on also. Took to dealer - Cost $400 for them to replace the ignition. Fixed every thing.

Sep 14, 2010 | 1999 Jeep Wrangler

1 Answer

I have a 99 Jeep Wrangler and the turn signals, wipers, and radio work when i turn the switch back to AC. But when i actually start my car none of the three work. No idea what it could be?


Very likely the ignition switch is bad. both run and accessory terminals should be engaged in the run position. Sounds like that's not happening.

Nov 18, 2009 | 1999 Jeep Wrangler

1 Answer

99 Wrangler AC Fan Sometimes doesn't work


Well if those two pins look melted, chances are there not making a good contact connection with the other side of the connector. Make sure your ground wires are clean and tight, and you should replace those melted pins. You really cant go much further until you resolve that issue.

Jul 31, 2009 | 1999 Jeep Wrangler

2 Answers

1997 jeep wrangler wont start


I had same problem. Ended up having to replace ignition switch, then gauges and jeep started right up

Apr 21, 2009 | 1997 Jeep Wrangler

1 Answer

99 jeep wrangler wipers only work on high setting


your switch is broken, take it in and get the switch replaced.

tepfy

Jan 09, 2009 | 1999 Jeep Wrangler

1 Answer

1988 Wrangler Ignition Switch Removal


There are four (sometimes two) bolts that hold the steering column to the dash. remove them & column will come down to let you get in there.
follow instruction sheet with switch. if you don't get it centered correctly it wont work correctly.

Jan 04, 2009 | 1988 Jeep Wrangler

Not finding what you are looking for?
1999 Jeep Wrangler Logo

632 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...