Question about 2006 Chevrolet Cobalt

1 Answer

Camshaft position sensor location

Engine light on. Put on machine and it said it was cam sensor . My car don't even have one on it .

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 4,057 Answers

725 camshaft sensor camshaft position sensor location - 646ec50d-5684-4925-a0d2-6ae7fc61c6f3.jpg2009 Chevy Cobalt SS Cam Sensor Location

Posted on Apr 12, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
csmock132

Clint Smock

  • 4669 Answers

SOURCE: how do you check and change a camshaft position

The camshaft sensor wouldn't explain the clattering noise. But a timing chain would explain both. Clattering from a loose chain and the camshaft sensor code from when the chain broke and the camshafts stopped turning.

Posted on Aug 02, 2010

matney68

Donnie Matney

  • 426 Answers

SOURCE: location of camshaft position sensor

under rotor button inside distributer

Posted on Jun 21, 2009

Anonymous

  • 39 Answers

SOURCE: Where is the camshaft position sensor located-99 Chevy Lumina 3.1

It's held down by one bolt right above the timing chain cover. It's next to the head that's facing toward the front of the car.

Posted on Feb 06, 2009

emissionwiz

Marvin

  • 85222 Answers

SOURCE: camshaft position sensor location

At the right rear of the engine under the intake manifold and to the left of the oil filter. You will probably need to go under the car to spot it, it's the sensor with a three-wire connector arranged vertically. But you can take it out from above. It's held in with a single bolt with an eight MM head located just above the sensor. Un-clip and remove the electrical connector. Unscrew the bolt with a socket wrench & extension bar. Wiggle and pull the sensor out.
here is a picture.
255f615.jpg

Posted on Apr 10, 2009

Anonymous

  • 218 Answers

SOURCE: Camshaft Position Sensor Location

IF U GO TO THE RIGHT SIDE OF THE ENGINE AND LOOK 4 INCHES BEHIND THE BELT IT WILL BE ON TOP OF THE TIMING COVER.THE WIRES WILL BE RED/WHITE,BLACK,BROWN/WHITE

Posted on May 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 saturn relay with engine light staying on. Auto zone says it is a p0340 camshaft position sensor a circuit (bank 1 or single sensor). Where is the sensor located and is it an easy fix.


DTC P0340 Camshaft Position (CMP) Sensor Circuit . has single sensor . This is circuit problem , testing the electrical circuit's for the sensor before replacing the sensor should be done . Do you know how to test sensor circuit's ?

How To Diagnose Check Engine Light Code P0340 Cam Position Sensor

Camshaft Position (CMP) Sensor
Right side of the engine, above the timing chain cover, under the power steering pump

Aug 18, 2018 | Saturn Cars & Trucks

1 Answer

2007 Saturn Outlook Cam Position Sensor Location 3.6 engine


(1) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 1
(2) Camshaft Position (CMP) Sensor - Intake Bank 1
(3) Camshaft Position (CMP) Sensor - Intake Bank 2
(4) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 2
(5) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 2
(6) Camshaft Position (CMP) Sensor - Exhaust Bank 2
(7) Generator
(8) A/C Compressor Clutch
(9) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 1
(10) Camshaft Position (CMP) Sensor - Exhaust Bank 1

Mar 22, 2018 | Saturn Cars & Trucks

1 Answer

Where is the cam position sensor on a 97 Hyundai elantra


Hi Zolo,here's a link to your camshaft position sensor. Duralast Camshaft Position Sensor SU4117 ReadReviews onDuralast SU4117 The Camshaft Position Sensoris located: Under hood, passenger side, upper engine area, mounted in engine block .Here's another on how to replace it.
Repair Guides Electronic Engine Controls Camshaft Position cmp Sensor...

Sep 28, 2016 | Hyundai Cars & Trucks

1 Answer

Where is cam shaft sensor located on a 08 saturn aura


Which engine ? This vehicle had option of six different engines , 2.4 , 3.5 , 2.8 , 3.0 , 3.2 , 3.6 And are you picking on the right part ? What code > DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit
It may not even be a cam sensor problem !
DTC P0340: Intake CMP Sensor Circuit

DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance
Camshaft Position (CMP) Actuator System
The camshaft position (CMP) actuator system is an electro-hydraulic operated device used for a variety of engine performance and operational enhancements. These enhancements include lower emission output through exhaust gas dilution of the intake charge in the combustion chamber, a broader engine torque range, and improved fuel economy. The CMP actuator system accomplishes this by changing the angle or timing of the camshaft relative to the crankshaft position. The CMP actuator simply allows earlier or later intake and exhaust valve opening during the four stroke engine cycle. The CMP actuator cannot vary the duration of valve opening, or the valve lift.
During engine OFF, engine idling conditions, and engine shutdown, the camshaft actuator is held in the Park position. Internal to the CMP actuator assembly is a return spring and a locking pin. During non-phasing modes of the camshaft, the return spring rotates the camshaft back to the Park position, and the locking pin retains the CMP actuator sprocket to the camshaft


It may

Jul 06, 2016 | 2008 Saturn Aura

2 Answers

The camshaft position sensor is bad but I don't know where it is located or how to change it


it depends on the vehicle. and you did not say what type of vehicle. most general motors C/S sensors are located at the front of the engine above the timing chain cover . some are located on the Rt. sice of the cylinder head

Apr 18, 2013 | Cars & Trucks

1 Answer

Where is the cam position sensor located on a 99 oldsmobile alero, how easy is it to install?


camshaft position sensor location on the V6 engine located at the front of the engine block below the power steering pump. the 4 cylinder engine camshaft position sensor location below ignition coil cover where coil cover say 2.4L TWIN camshaft sensor in that location below coil cover. you will see red or red white wires connected to it.

Apr 14, 2011 | 1999 Oldsmobile Alero

2 Answers

How do I replace the CAM sensor on a 1996 dodge neon?


Hi, my name is John I will do my best to assist you.

To Remove
  1. Disconnect the negative battery cable.
  2. Disconnect the filtered air tube from the throttle body and air cleaner housing.
  3. For SOHC engines, remove the air cleaner inlet tube.
  4. For SOHC engines, detach the electrical connectors from the engine coolant sensor and the camshaft position sensor.
  5. For DOHC engines, unplug the electrical connector from the camshaft position sensor.
  6. For SOHC engines, remove the brake booster hose and the electrical connectors form the holders on the end of the cylinder head cover.
  7. Unfasten the camshaft position sensor mounting screws, then remove the sensor.
  8. Loosen the screw/bolt attaching the target magnet to the rear of the camshaft.
To Install: NOTE: The target magnet has 2 locating dowels which fit into the machined locating holes in the end of the camshaft.

  1. Install the target magnet in the end of the camshaft. Tighten the retainer to 30 inch lbs. (3.4 Nm).
  2. Install the camshaft position sensor. Tighten the sensor mounting screws to 80 inch lbs. (9 Nm).
  3. For SOHC engines, place the brake booster hose and the electrical harness in the holders on the end of the valve cover.
  4. Attach the electrical connector(s) to the camshaft position sensor and coolant temperature sensor (if necessary).
  5. Install the air cleaner inlet tube and the filtered air tube.
  6. Connect the negative battery cable.
The camshaft position sensor is mounted to the rear of the cylinder head - SOHC engine shown


tecnovative_139.gif
Location of the camshaft position sensor - DOHC engine shown

tecnovative_140.gif

Unfasten the retaining bolt, then remove the target magnet from the rear of the camshaft - SOHC shown, DOHC similar

tecnovative_141.gif

The target magnet has 2 locating dowels for proper alignment during installation

tecnovative_142.gif

Feb 20, 2011 | 1996 Dodge Neon

3 Answers

2001 dodge ram 1500 5.9 camshaft position sensor location?


CAMSHAFT POSITION SENSOR 2001 Dodge Truck RAM 1500 1/2 ton 2WD 5.9L SFI 8cyl The Camshaft Position Sensor is located: Under hood, center, upper engine area, rear of intake manifold, mounted in distributor

If this is helpful.Please leave ositive Feedback. Thanks, SnugglePants

Oct 21, 2009 | 2001 Dodge Ram 1500 Truck 2WD

4 Answers

Where is the camshaft position sensor located on a 2004 dodge stratus 4 cyl 2.4L engine


the camshaft sensor is mounted on the camshaft housing located on the end of the cylinder head.

Jul 08, 2009 | 2004 Dodge Stratus

2 Answers

Engine misfire or flat spot when accelorating put occasionally


the camshaft position sensor is right around the crankshaft. there is a magnetic wheel at the end of the camshaft that the sensor uses to produce the signal.

Jun 10, 2009 | 2005 Ford Focus

Not finding what you are looking for?
2006 Chevrolet Cobalt Logo

1,451 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...