- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Amazon.cahttps://www.amazon.ca > Exterior-Replacement-CITR...
1.Remove all existing mirror glass from the mirror assembly plastic backing plate. 2.Clean the backing plate with rubbing alcohol and clean the back of the new ...
$70.50 · ‎In stock
Hi Michelle , what make model an year vehicle ? On some vehicles this is function is controlled by a door module .
In order to control outside rearview mirror operations, as well as other door functions, the front door modules must be powered up. For this purpose, battery voltage is supplied from the rear fuse block, through separate circuits, to each front door module. Each front door module is separately grounded through a ground stake. The front door modules also use these power and ground supplies to drive the mirror motors, and to provide power and ground to window and lock switches and door lock actuators. In addition, the driver door module (DDM) uses these power and ground supplies to power the driver door switch assembly (DDSA) and integral mirror control switches.
Could have DTC'S - diagnostic trouble codes stored in BCM - body control module .
DTC B1544 01: Mirror Motors Common Circuit Short to Voltage
DTC B1544 02: Mirror Motors Common Circuit Short to Ground
DTC B1544 04: Mirror Motors Common Circuit Open Circuit
DTC B1600 01: Mirror Motor 1 (vertical) Circuit Short to Voltage
DTC B1600 02: Mirror Motor 1 (vertical) Circuit Short to Ground
DTC B1600 04: Mirror Motor 1 (vertical) Circuit Open Circuit
DTC B1605 01: Mirror Motor 2 (horizontal) Circuit Short to Voltage
DTC B1605 02: Mirror Motor 2 (horizontal) Circuit Short to Ground
DTC B1605 04: Mirror Motor 2 (horizontal) Circuit Open Circuit .
? 4:06 https://www.youtube.com/watch?v=2LAqSfV-swI
May 23, 2010 - Uploaded by Decibel Car
Want to replace your wing mirrors with aftermarket ones ? Had someone in a shopping mall car park break ...
Remove the screws that hold the mirror and remove it from the door. Attach the new mirror. Reconnect the electrical connector and make sure you test the new mirror before putting the parts back into place. Reverse the entire procedure to reassemble the door trim panel.
The easiest way is to buy a pattern mirror lens and stick it over the broken glass, these lenses are available on-line or at some parts shops. The harder way is to remove the mirror cover and strip the mechanism out and refit to base bracket
it's just clipped on. order the new glass and it will be obvious where the clips are on the back. the glass and backing are one unit, this is clipped onto the mirror housing in the middle.
Remove the door handle bezel.Remove the power window/door lock switch bezel.Remove the rearview mirror fastener trim cover.Remove the 4 door trim panel retaining screws.One that was behind the mirror trim cover,behind the switch panel,behind the door handle bezel,and one at the bottom corner.Lift the door trim panel up from the door to disengage the trim panel clips.Remove the front radio speaker. Disconnect the power mirror wiring connector.Remove the 3 bolts to the mirror.
your mirror control switch has 9 wires.,your drivers door mirror has 5 wires color coded .from your mirror control switch to your drivers siide mirror / 0.5 black .0.5 brown. 0.5 brown. 0.5 black. 0.5 black.
your passenger mirror wires are 0.5 blue/black .0.5 blue/grey. 0.5 blue/white. the passenger mirror has a ground cable 0.5 brown.
the passenger mirror wire 0.5 green/white connects to a 5amp fuse/F25 onto F31 5amp to a wire 0.75 green/yellow.back to the mirror control switch.
×