Question about 2000 Chevrolet Silverado 1500

Open Question

Torque specs for crankshaft and connecting rods 2000 5.3 vortec

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 379 Answers

SOURCE: torque specs.

connecting rod = first pass 18 ft lbs , second pass 75 degrees

main bearings = first pass 37 ft lbs , second pass 77 degrees

wow that wasn't easy to find for some reason .

Posted on Jan 01, 2009

Ad

Anonymous

  • 17 Answers

SOURCE: I need the torque specs and sequence on a 1998 chevy 350 vortec

Vortecs are a little different that old school small blocks, grab a Haynes or Chiltons, the cross patterns and specs are simply diagramed. Vortec, as any really, start with 25# then 45# and then final torque which I believe is around 70-75# but to be sure verify with the manual. AutoZones, Murry's, Adavance auto all carry the books, Cheap insurance.
Dan

Posted on Apr 25, 2009

SOURCE: need torque specs for a 85 s10 chevy with a 2.5 engine?

here you go!

1dd4f4a.gif93a64e1.gif

Posted on Jun 21, 2009

Anonymous

  • 106 Answers

SOURCE: i need bolt torque specs for a 2006 chevy cobalt

if you just go to a mecanic and ask what are the specks on that they should know but i think if you just tighten them down with an impact wrench till it is really tight after ou start the car it will run like **** then it will work its self out

Posted on Nov 17, 2009

wilsodfarm

Donnie Wilson

  • 986 Answers

SOURCE: Torque Specs for Head Bolts on 1997 GMC Sierra V8 5.0 Vortec?

.0L Torque Specs Belhousing to engine bolts 28-38 ft/lbs Camshaft sprocket bolt 40-45 ft/lbs Camshaft thrust plate to engine block bolts 108-144 in/lbs Crankshaft pulley to vibration damper bolts 35-50 ft/lbs Cylinder head bolts -1979-1992 --Step 1 55-65 ft/lbs --Step 2 65-72 ft/lbs -1993-up --Step 1 25-35 ft/lbs --Step 2 45-55 ft/lbs --Step 3 75-85 ft/lbs Differential shaft lock bolt 15-30 ft/lbs Driveshaft U-joint to pinion flange bolts 70-95 ft/lbs Exhaust manifold bolts 26-32 ft/lbs Flywheel mounting bolts 75-85 ft/lbs Front engine mount nuts 72-98 ft/lbs Intake manifold to head bolts --Step 1 96 in/lbs --Step 2 16ft/lbs --Step 3 23-25 ft/lbs Intake manifold (upper intake to lower) 12-18 ft/lbs Oil filter insert to engine block adapter bolt 20-30 ft/lbs Oil pan mounting bolts -1979 --Step 1 (Large bolts) 11-13 ft/lbs --Step 1 (Short bolts) 7-9 ft/lbs --Step 2 (Large Bolts) 15-17 ft/lbs --Step 2 (Short Bolts) 10-12 ft/lbs -1980 to 1987 9-11 ft/lbs -1988 to 1993 6-9 ft/lbs -1994-up 110-144 in/lbs Oil pickup tube to main bearing cap nut 22-32 ft/lbs Oil pickup tube to oil pump bolts -1979 to 1987 10-15 ft/lbs -1988-up 12-18 ft/lbs Oil pump mounting bolts 22-32 ft/lbs Pinion bearing preload 8-14 in/lbs Pressure plate to flywheel bolts 12-24 ft/lbs Rocker arm fulcrm bolts 18-25 ft/lbs Spark plugs 7-14 ft/lbs Timing chain cover bolts 12-18 ft/lbs Vibration damper to crackshaft bolt 110-130 ft/lbs Wheel lug nuts 85-105 ft/lbs

Posted on Mar 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque does my kohler k662 spec # 3966c produce at the crank?


Kohler Small Engine Connecting Rod Torques

outdoorpowerinfo.com/engine_specs/kohler_rod_torques.asp
Engine Connecting Rod Torques for Kohler small engines used on a variety of outdoor power equipment applications. ... Series, Engine Model, Engine Type, Rod Torque .....K-SERIES, K662, Air Cooled Horizontal Crankshaft Twin, 35 ft-lb.

Sep 24, 2015 | Cars & Trucks

2 Answers

What the torque specs. For a 2002chevys10 4.3vortex mains and rod bearing


Torque Specs Database

Type: Dim: Length: Head: Nut Grade: 20 Ft-Lbs 240 In-Lbs 27.12 N-m Connects: Connecting Rod To Engine Block Years: All Vote Record: Vote Note: Vortec - Rod Cap Nuts - 2 Steps: 20 FtLbs; +70degs

http://ww2.justanswer.com/uploads/ZZdaryl/2009-06-14_153454_torque.pdf

Main Bearing Cap Bolt 4.3L Step 1 15 ft lbs (20) Step 2 Additional 73 Degrees

i don't know if that's correct for main bearing caps since another link states it's much higher

4 3 Vortec Piston Specs eHow

hopefully a GM guy will chime in to confirm the main bearing torque

the rod bearing torques are the same on all the other links

Mar 25, 2015 | 2002 Chevrolet S-10

1 Answer

Crankshaft & connecting rod torque specs for a 98 jaguar xj8 4.0


crank is 105ft lb final torque connecting rod is 40 ft lb final torque. you can check on auto zone libary

Oct 15, 2014 | Cars & Trucks

1 Answer

Toque specs on a 1971 in line 6 mercury comet's rod bearings and the clearance between the bearing and crankshaft


TORQUE SPEC FOR ROD BEARING BOLTS 19 - 24 FT LBS TORQUE SPEC FOR MAIN BEARING BOLTS 60 - 70 FT LBS, CRANKSHAFT PULLEY BOLT 85 - 100 FT LBS. MAIN BEARING OIL CLEARANCE .0005 - .0022 CONNECTING ROD OIL CLEARANCE .0008 - .0015 / SHAFT END PLAY .004 - .008 / AND ROD SIDE CLEARANCE IS .004 - .011 HOPE THIS HELP THIS INFORMATION I GAVE YOU IS INLINE 6 -200 AND INLINE 6 - 250 ENGINES

Nov 11, 2011 | Cars & Trucks

1 Answer

What is the torque specs for 2000 4.3 connecting rod caps?


According to Torkspec.com, for GM 4.3l 262 ci V6 the specs are as follows;



Type: Dim: Length: Head: Nut Grade: 20 Ft-Lbs 240 In-Lbs 27.12 N-m Connects: Connecting Rod To Engine Block Years: All Vote Record: Vote Note: Vortec - Rod Cap Nuts - 2 Steps: 20 FtLbs; +70degs

Jan 09, 2011 | 2000 Chevrolet S-10

1 Answer

Need torque for a 2000 Toyota Celicia GT 1.8L


Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Mar 18, 2010 | 2000 Toyota Celica

1 Answer

2000 Isuzu Trooper Specs


Tighten the connecting rod cap nuts
Torque : 54 N·m (5.5 Kg·m/40 lb ft)

Jun 30, 2009 | 2000 Isuzu Trooper

1 Answer

I'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.


1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)

2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)

3. Measure the oil clearance between the connecting rod and the crankshaft.

    1. Remove the connecting rod cap nuts and the rod caps (12). Arrange the removed rod caps in the cylinder number order.
    2. Clean the rod bearings and the crankshaft pins.
      1. Carefully check the rod bearings. If even one bearing is found to be damaged or badly worn, the entire bearing assembly must be replaced as a set. Reinstall the bearings in their original positions. Apply plastigage to the crank pin.
      2. Reinstall the rod caps (12) to their original positions. Tighten the rod cap nuts. Torque: 54 Nm (40 ft. lbs.) Note: Do not allow the crankshaft to rotate.
      3. Remove the rod caps.
        1. Measure the width of the plastigage and determine the oil clearance. If the oil clearance exceeds the limit, replace the rod bearing as a set. Standard: 0.019 mm - 0.043 mm (0.0007 inch - 0.0017 inch) Limit: 0.08 mm (0.003 inch)
        2. Clean the plastigage from the bearings and the crankshaft pins.

May 21, 2009 | 2000 Isuzu Rodeo

1 Answer

Torque specs


2002 2.0L Duratech.

Don't have 2004 2.3L

  • NOTE: Use new connecting rod bearing cap bolts.
    NOTE: Do not fully tighten the connecting rod bearing cap bolts at this stage.
    Install the bearing caps.
  • Rotate the crankshaft through 180 degrees and insert pistons 2 and 3.
  • Position the corresponding bearing shells, clean and free of oil, into the connecting rod and the connecting rod bearing cap.
  • Coat the inner side of the bearing shells with engine oil.
  1. NOTE: The crankshaft must rotate freely, if necessary check and adjust the bearing clearances.
    Tighten the main bearing and connecting rod bearing bolts.
    1. Tighten the main bearing bolts in two stages.
      • Stage 1: 25 Nm.
      • Stage 2: 60 degrees.
    1. Tighten the connecting rod bearing bolts in two stages.
      • Stage 1: 35 Nm.
      • Stage 2: 90 degrees.
96fc939.gif

Apr 28, 2009 | 2004 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

606 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...