Where can I get intake valve timing solenoid

Question edited for clarity, the 'P' on the code is important :>D
Question moved to model category.

P1111 Nissan Code - Intake Valve Timing Control Solenoid ...

https://www.engine-codes.com > p1111_nissan
The intake valve timing control solenoid valve is activated by ON/OFF pulse duty (ratio) signals from the Engine Control Module (ECM). The intake valve timing ...

Code P1111 Nissan: Intake Valve Timing Control Solenoid ...

https://www.autocodes.com > p1111_nissan
Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the ...

code p 1110 refers to the valve timing control solenoid
and not the cam position sensor
replace or repair that unit
code p 1111 refers to the same solenoid circuit bank 1

P1110 Intake Valve Timing Control Circuit (Bank 1)

Code P1110 is the valve timing control solenoid
and not the cam position sensor ,replace or repair that unit

P1136 NISSAN - Intake Valve Timing Control Solenoid Valve Circuit Bank 2
Possible causes- Intake valve timing control solenoid valve bank 2 circuit is open or shorted.
- Intake valve timing control solenoid valve bank 2 circuit connectors
- Intake valve timing control solenoid valve bank 2 Tech notes Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code.

P1111 is intake air temperature, which has nothing to do with intake variable valve timing. If the code is P1110 then yes you have a intake variable valve timing but before you throw a solenoid in the mix make sure you are properly changing oil on time and do do have low oil level you basically have poor oil maintance for P1110 to take place

P1110 Intake Valve Timing Control Solenoid Error

From what I've read, the plunger within this solenoid gets stuck, causing this error. Some have had success with applying lube to this part, while others have had to replace it.


The VTC solenoid valve is part of the Valve Timing Control System. The purpose of the system is to achieve optimum valve timing, thus improving engine performance.

The system will vary the intake valve timing according to engine speed, and other inputs received from the coolant temperature and throttle position sensors. The ECM controls the position of the intake camshaft, by controlling the oil pressure to the intake camshaft pulley hub. When the ECM energizes the solenoid, oil pressure is supplied to the pulley hub, changing the position of the hub, thereby advancing the intake valve timing.

1 Remove the VTC valve from the vehicle.

2 Using a fused jumper wire, apply battery voltage to terminal 1, and ground to terminal 2.

3 If the valve is functioning correctly, the plunger shaft in the valve should be extended.

4 If the plunger is not extended, replace the VTC solenoid.

----

1 Disconnect the wiring harness connector from the VTC valve.

2 Using a suitable wrench, remove the VTC from the cylinder head.

To install:

1 Install the VTC in to the cylinder head, by first hand tightening, then using a wrench.

2 Plug the wire harness connector into the VTC valve.

If you can supply me with all the codes your vehicle is showing, I can assist you. As far as the P1111 DTC goes I have listed the info below with some possible solutions.

P1111- Intake Valve Timing Control Solenoid Valve Circuit Bank 1

Intake valve timing control solenoid valve is activated by ON/OFF pulse duty (ratio) signals from the ECM. The intake valve timing control solenoid valve changes the oil amount and direction of flow through intake valve timing control unit or stops oil flow. The longer pulse width advances valve angle. The shorter pulse width retards valve angle. When ON and OFF pulse widths become equal, the solenoid valve stops oil pressure flow to fix the intake valve angle at the control position. The code is triggered when an improper voltage is sent to the ECM through intake valve timing control solenoid valve. Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code.

Possible Causes:
- Intake valve timing control solenoid valve bank 1 circuit is open or shorted.
- Intake valve timing control solenoid valve bank 1 circuit connectors
- Intake valve timing control solenoid valve bank 1
- Dirty Oil

Possible Solutions:
- Change Oil
- Replace Intake valve timing control solenoid valve

NISSAN OBDII DTC

P1105 Manifold Absolute Pressure/Barometric Pressure Switch Solenoid Circuit

P1110 Intake Valve Timing Control Circuit (Bank 1)

P1120 Secondary Throttle Position Sensor Circuit

P1125 Tandem Throttle Position Sensor Circuit

P1132 Intake Valve Timing Control Position Sensor (Bank 1)

P1135 Intake Valve Timing Control Circuit (Bank 2)

P1137 Intake Valve Timing Control Position Sensor (Bank 2)

P1140 Intake Valve Timing Control Position Sensor (Bank 1)

P1145 Intake Valve Timing Control Position Sensor (Bank 2)

P1148 Closed Loop Fault Detected (Bank 1)

P1168 Closed Loop Fault Detected (Bank 2)

P1210 Traction Control System Signal Fault

P1220 Fuel Pump Control Module Fault

P1320 Ignition Control Signal Fault

P1335 Crankshaft Position Sensor Circuit

P1336 Crankshaft Position Sensor circuit

P1400 EGR/EVAP Control Solenoid Circuit

P1401 EGR Temperature Sensor Circuit

P1402 EGR System Fault Detected

P1440 EVAP Canister System Leak Detected

P1441 EVAP Vacuum Cut Valve Bypass Valve Circuit

P1443 EVAP Canister Control Vacuum Switch Circuit

P1444 EVAP Canister Purge Volume Control Valve Circuit

P1445 EVAP Purge Volume Control Valve

P1446 EVAP Canister Vent Valve Circuit

P1447 EVAP Canister Purge Flow/Volume Control Valve Circuit

P1448 EVAP Vent Control Valve Circuit

P1490 EVAP Vent Control Valve/Bypass Valve Circuit

P1491 EVAP Vacuum Cut Valve/Bypass Valve Circuit

P1492 EVAP Canister Purge Control Valve/Solenoid Valve

P1605 Transmission Control Module A/T Diagnosis Communication Line Fault

P1705 Throttle Position Switch Circuit

P1706 Park Neutral Position Switch Circuit

P1760 Overrun Clutch Solenoid Valve Circuit
P1900 Cooling Fan Control Circuit
sorry but your code reader is not reading manufacturers codes ,if an american market vehicle then you should be able to read them but if this is a europeon model then how did you manage to get this code??

P0235....Turbo/Super Charger Boost Sensor 'A' Circuit

this is a generic code if its any help

Accelerator Pedal Position Error.

P2138 - Accelerator Pedal Position Sensor Circuit Range / Performance Problem

Clear the code - if it recurs, change the sensor.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.