Dtc got code P0446 - what does it mean?

Testing diagnostic's associated for the codes is how to find the fix. Assuming as to a fix would only be a guess . Your best bet would be to take it to a qualified repair shop .OR you could look on youtube .
P0101 GM Digital Mass Air Flow Sensor Diagnostics and Troubleshooting by...
P0113 OBD II DTC Engine Code for 2002 Chevy Trailblazer
EVAP Vent Solenoid Code P0446

2004 Buick Rainier code p0446:

I'm not sure what part to buy or where to find it. Can't find this answer anywhere online. Please help. This is code p0446 and non other.

P0446 Evaporative Emission Control System Vent Control Circuit Malfunction The code P0446 is set when the engine computer recognizes a fault or restriction at the vent control part of the Evaporative emission control system (EVAP). The description of the fault varies between different car manufacturers, but one thing is common, the code P0446 doesn't directly point to a defective part; some testing might be required to pinpoint the faulty component. What can cause the code P0446: - faulty vent control valve - blockage at the vent hose, vent filter or vent control valve - open or short in the vent control valve circuit - bad charcoal canister - EVAP system leak - faulty EVAP system pressure sensor - bad vacuum switching valve (VSV) - stuck open purge valve (solenoid)

try googling for the error code

Hi there:
DTC P0446 - Evaporative Emmission Control System Vent Control Circuit

A code P0446 could mean one or more of the following has happened:
- Faulty vent valve
- Open, short or excessive resistance on Vent valve control circuit
- Blockage of vent valve
- Bad PCM

About the possible solutions with this trouble code, here are some things to try:
- Replace Vent valve
- Repair open, short, or resistance problem in control circuit
- Repair open, or short, or resistance problem in power circuit
- Replace PCM

Additionally, I suggest to check this information in the LINK.

Hope this helps.

P0446 has nothing to do with the canistor !
DTC P0446 Evaporative Emission (EVAP) Vent System Performance
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inches H2O in a calibrated time, this DTC sets.
DTC P0452 Fuel Tank Pressure (FTP) Sensor Circuit Low Voltage


How to troubleshoot an EVAP Pressure Sensor problem P0452 GM

EVAP Vent Solenoid Code P0446 The solenoid is stuck open !

DTC P0446 - Evaporative Emission Control System Vent Control Circuit Malfunction
Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test. There will be no obvious symptoms to driver, other than MIL illumination.

A code P0446 could mean one or more of the following has happened:
Faulty vent valve
Open, short or excessive resistance on Vent valve control circuit
Blockage of vent valve
Bad PCM


With a P0446 OBD-II trouble code, here are some things to try:
Replace Vent valve
Repair open, short, or resistance problem in control circuit
Repair open, or short, or resistance problem in power circuit
Replace PCM


Hope this helps (remember to rating this free answer and leave us some testimonial comment).

DTC P0446 - Evaporative Emmission Control System Vent Control Circuit
Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test. A code P0446 could mean one or more of the following has happened:

• Faulty vent valve
• Open, short or excessive resistance on Vent valve control circuit
• Blockage of vent valve
• Bad PCM

Possible Solutions

• Replace Vent valve
• Repair open, short, or resistance problem in control circuit
• Repair open, or short, or resistance problem in power circuit
• Replace PCM

DTC P0452 - Evaporative emission control system, pressure sensor low imput
DTC P0453 - Evaporative emission control system, pressure sensor high imput

The PCM monitors the EVAP control system FTP sensor input signal to the PCM. The test fails when the signal average jumps above a minimum allowable calibrated parameter. If both codes are present, it sounds like your fuel tank pressure sensor has failed.

The sensor is on top of the tank and you will have to remove the tank. But your symptoms are pointing to more than just the sensor. You may have wiring problems.


Hope this helps (remember to rate and leave a comment about this free answer).

DTC P0446 - Evaporative Emmission Control System Vent Control Circuit

Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test.

Symptoms: There will be no obvious symptoms to driver, other than MIL illumination.


Causes: A code P0446 could mean one or more of the following has happened:

• Faulty vent valve
• Open, short or excessive resistance on Vent valve control circuit
• Blockage of vent valve
• Bad PCM

Possible Solutions: With a P0446 OBD-II trouble code, here are some things to try:

• Replace Vent valve
• Repair open, short, or resistance problem in control circuit
• Repair open, or short, or resistance problem in power circuit
• Replace PCM

Hope helps (remember to rate this answer).

DTC P0446 - Evaporative Emmission Control System Vent Control Circuit

Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test.

Symptoms: There will be no obvious symptoms to driver, other than MIL illumination.


Causes: A code P0446 could mean one or more of the following has happened:

• Faulty vent valve
• Open, short or excessive resistance on Vent valve control circuit
• Blockage of vent valve
• Bad PCM

Possible Solutions: With a P0446 OBD-II trouble code, here are some things to try:

• Replace Vent valve
• Repair open, short, or resistance problem in control circuit
• Repair open, or short, or resistance problem in power circuit
• Replace PCM

Hope helps (remember to rate this answer).