Question about 2009 Ford Edge

Open Question

2009 ford edge 3.5 liter water pump remove replace

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
bradk99

Brad Keller

  • 2 Answers

SOURCE: Fuel Pump 2000 Ford Mustang

remove it from what? You should have dropped the gas tank - it's removed from the tank after it's lowered from the car. Two straps, the filler neck (which is a little tricky - make sure the tank is supported by a jack).

Posted on Jun 14, 2008

Ad

Anonymous

  • 1010 Answers

SOURCE: water pump

A manual will have pictures and everything.
Just replaced mine. Five bolts in bracket holding tension idler, A/C compressor (if applicable) and power steering pump must be removed to access 3 bolts in water pump. Just push aside enough to access remaining bolts. Email at dabeam@sbcglobal.net if additional info is needed. Also, diagram serpentine belt before removing. Took me at least 15 attempts and 20 minutes to figure out

Posted on Jun 25, 2008

dan

  • 651 Answers

SOURCE: defective water pump on a ford edge

your local auto store should have one.

Posted on Dec 17, 2008

Anonymous

  • 7 Answers

SOURCE: Remove fan from water pump on a 1997 Ford F150 4.2 Liter

There is a special tool that is required to hold the fan clutch. Then the fan screws out of the clutch. The tool can be bought or rented at your friendly parts store like autozone, etc. It will look something like this:  http://www.amazon.com/Universal-Clutch-Water-Pulley-Holding/dp/B000RT924E

Posted on Jan 19, 2009

Anonymous

  • 149 Answers

SOURCE: 2005 Dodge Grand Caravan 3.8 liter engine needs water pump replac

3.3 & 3.8 same block. V6 no special tools needed

Posted on Jan 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a power steering belt on a 2009 Ford Edge..3.5l


You need a stretchy belt remover (special tool) for that.

I’m happy to assist further over the phone at https://www.6ya.com/expert/kim_3202917d7c587455

Dec 20, 2016 | 2009 Ford Edge

1 Answer

How to change water pump on a 2009 Ford Fusion


2.3L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Loosen the 3 coolant pump pulley bolts.
  4. Remove the accessory drive belt.
  5. Remove the 3 bolts and the coolant pump pulley.
    1. To install, tighten to 15 ft. lbs. (20 Nm).
  6. Remove the 3 bolts and the coolant pump.
  7. Remove and discard the O-ring seal.
    1. To install, tighten to 89 inch lbs. (10 Nm).


25940856-ldxojubx5kaly1k2zv3zks4n-2-0.gif Fig. Exploded view of the water pump-2.3L engine


To install:
  1. To install, reverse the removal procedure.
  2. Lubricate the O-ring seal with clean engine coolant.
  3. Fill and bleed the cooling system

3.0L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Remove the coolant pump belt.
  4. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley.


25940856-ldxojubx5kaly1k2zv3zks4n-2-1.gif Fig. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley

5, Disconnect the heater hose from the coolant pump.
6. Disconnect the coolant pump-to-engine hose and position aside.
7. Remove the 3 bolts from the coolant pump assembly.
8. Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly.


25940856-ldxojubx5kaly1k2zv3zks4n-2-3.gif
Fig. View of the water pump and related components-3.0L engine

To install:
  1. Connect the coolant pump-to-thermostat housing hose and reposition the clamp.
  2. Position the coolant pump assembly and install the 3 bolts:
    1. Tighten to 89 inch lbs. (10 Nm).
    2. Tighten the 3 bolts an additional 90 degrees.
  3. Connect the coolant pump-to-engine hose and the heater hose.
    NOTE
    Install the coolant pump drive pulley flush with the end of the camshaft.
  4. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley.



25940856-ldxojubx5kaly1k2zv3zks4n-2-6.gif Fig. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley

5. Install the coolant pump belt.
6. Fill and bleed the cooling system.

Nov 04, 2015 | 2009 Ford Fusion SE

1 Answer

Where can I get printable step-by-step instructions for replacing a water pump?


Try Here:
http://www.ebay.com/itm/FORD-EDGE-2006-2007-2008-2009-2010-FACTORY-REPAIR-SERVICE-WORKSHOP-MANUAL-/121667421696?hash=item1c53f18600&vxp=mtr
It's almost never available free, and if it is, not sure I would trust it. This is $10.00 and would cover anything you need to do. "Step by step". If you find it on this site, (fixya) it's because someone shared this with you. I only have 1996-2003 all models. Good luck!

Jun 14, 2015 | 2007 Ford Edge SE

1 Answer

Ford escort 1.6 16v zetec engine water pump broke so removed timing belt and water pump replaced water pump timing belt after some time replaced crank pully turned crank pully by hand seemed...


NOOOOooooo!!!!
You have the timing off. If you crank the engine you will bend every valve in the head and be looking at $2K in repairs.
What stopped the engine from turning is the valves are hitting the piston.


Ford Zetec 2 0 liter timing belt replacement Part HD

Jan 31, 2018 | Ford Escort Cars & Trucks

2 Answers

How do you remove the fan from 1998 f150 4.2 liter


how do you remove the fan and fan clutch from 1998 f150 4.2 liter engine. i am trying to replace the water pump but i cannot get the fan to break loose . i cannot figure how to stop pump from turning while trying to loosen the bolt or nut that holds the fan clutch on the water pump shaft . is there a special tool to help me with this

Jul 15, 2010 | 1998 Ford F150 Regular Cab

1 Answer

2005 Dodge Grand Caravan 3.8 liter engine needs water pump replac


3.3 & 3.8 same block. V6 no special tools needed

Sep 29, 2009 | 2005 Ford F-150

1 Answer

Remove fan from water pump on a 1997 Ford F150 4.2 Liter


There is a special tool that is required to hold the fan clutch. Then the fan screws out of the clutch. The tool can be bought or rented at your friendly parts store like autozone, etc. It will look something like this:  http://www.amazon.com/Universal-Clutch-Water-Pulley-Holding/dp/B000RT924E

Jan 16, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Water pump


A manual will have pictures and everything.
Just replaced mine. Five bolts in bracket holding tension idler, A/C compressor (if applicable) and power steering pump must be removed to access 3 bolts in water pump. Just push aside enough to access remaining bolts. Email at dabeam@sbcglobal.net if additional info is needed. Also, diagram serpentine belt before removing. Took me at least 15 attempts and 20 minutes to figure out

Jun 25, 2008 | 1989 Ford Ranger

Not finding what you are looking for?
2009 Ford Edge Logo

Related Topics:

863 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...