What are the rear brake rotor minimum thickness specs?

What year is the vehicle .
The year is importent because of the metal the rotors are made of .
Not many stores will turn rotors at all anymore .
You can thank China a lot of them are chrome plated and this is supposed a federialey controlled speic no such luck Class ACTION SUITE

Auto Parts Stores have books for that spec

Rear Brakes JC5/JH5 Utility Only
Rotor Discard Thickness* .............................. 28.50 mm (1.122 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 29.0 mm (1.142 inch)
Rotor Thickness-new .................................... 30.0 mm (1.181 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

Rear Brakes JH6
Rotor Discard Thickness * ............................. 27.50 mm (1.082 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 28.0 mm (1.102 inch)
Rotor Thickness-new .................................... 29.0 mm (1.141 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

rotor thickness is cast into the rotor but if you cannot find it then contact a brake shop as they have the minimum measurements for all vehicles .

lordFord's answer was arrogant and absolutely useless. Brake rotor thickness specifications are dependent upon the Year/Make/Model of the vehicle, it has nothing to do with your "state/province" or "common sense." Most brake rotors have the minimum thickness spec. stamped on the rotor itself. The service department of the dealership for whatever brand of vehicle you have, will be able to provide the spec. to you as well. A visual inspection may point to obvious signs such as scoring, cracks or pitting, and a vibration when applying the brakes, could be a warped rotor.

The minimum rotor specs is stamped on the rotor and is different with each manufacture which sets the standard. Measure the thickness with a micro-meter. Replace the rotor if it is below or near the minimum or has been grooved by worn pads.

All are different, on the back side of the brake rotor , will have a stamp with (MIN) and some number after it the will be the minimum spec thickness for the brake rotor.

your brake rotors are warped, if your vehicle is equipped with rear drum brakes have them cleaned and adjusted to keep your front brakes from working too hard and becoming warped, also replacing the front rotors is better than resurfacing them because after bieng resurfaced they are thinner and are more prone to becoming warped again

MINIMUM THICKNESS FOR FRONT BRAKE ROTOR IS. 0.972

there is many kind of brake system of ur truck here i will send u everything about the brake and i hope its help

Rear Brakes JC3

Rotor Discard Thickness* 18.50 mm/0.728 in Rotor Minimum Allowable Thickness After Refinish 19.0 mm/0.748 in Rotor Thickness (new) 20.0 mm/0.787 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JC4

Rotor Discard Thickness* 28.50 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring1 .50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH2

Rotor Discard Thickness* 28.50 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH6

Rotor Discard Thickness* 27.50 mm/1.082 in Rotor Minimum Allowable Thickness After Refinish 28.0 mm/1.102 in Rotor Thickness (new) 29.0 mm/1.141 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH7

Rotor Discard Thickness* 28.5 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this Specification. After refinishing the rotor, replace any rotor that does not meet the minimum or discard thickness specifications.