I have a 99 dakota sport only had it for 3 months and the whole time it would sputter for about 15 to 20 seconds when started cold but would clear right up i just replaced plugs and wires three weeks ago and its just started sputtering constantly codes say missfire number 2 cylinder so i changed plugs and wires again but still missifiring i was thinking injector i unhooked #2 injector while engin running and no difference
Usually if you know which cylinder, you check spark--fuel--compression on that cylinder.
You could do cylinder balance test, engine idling, kill each cylinder, one at a time. If you kill a cylinder that has no effect on rpms, that cylinder is dead for some reason, spark--fuel--compression?
I usually kill spark and do it quickly.
SOURCE: 2004 Neon SXT cylinder misfire
TRY REPLACING THE CRANKSHAFT POSITION SENSOR..HAVE SEEN THESE CAUSE MISFIRES AND LOW VOLTAGE DTCS AS PCM THINKS VEHICLE IS NOT RUNNING..ALTERNATOR MAY NOT BE PUTTING OUT PROPERLY
SOURCE: getting a code P0304 on my 1999 Dodge 1500 5.2L.
the code that is given means that the coil, plug ,plug wires, for that cylinder could be bad, check spark plug and see if this is the problem or a bad wire.
SOURCE: Misfire cylinder 5 2000 dodge dakota
when u press the gas pedal to go this opens the throttle valve, the idle speed of your engine is computer controlled, this is done by the ISC (idle speed control) airbypass valve, these parts get full of gunk and then get a stalling problem at or near idle, clean them by doing the following, if u don't understand the instructions seek help from your friend.
, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.
SOURCE: MIL indicates cylinder misfire on 1, 3, and 5
Check for
vacuum leaks on intake manifold,
the air tube between the air filter.
intake manifold vacuum hose.
===
clean throttle plate with Berryman carburator cleaner
SEE sample picture HERE
===
Also remove carbon built up behind the EGR valve and the EGR passage tube.
===
Vacuum leak WILL offset the intended 14.7 to 1 air fuel ratio.
More un-metered air (leaks) will lean out the fuel mixture.
Use small amount of Berryman carb clearer at potential air leak area will help you identify trouble spot.
At idle,just spray and listen for the RPM surge.
The in-rush of carb clearer will increase the RPM on the motor.
Record the problem spot(s) and address it later.
===
EGR carbon built up require 2+ hours to clean from start to finish.
You will need a new EGR base gasket before your start.
Locate and remove the EGR valve after the vehicle is cool down.
Carefully record the connector and vacuum line (for older vehicle) location by drawing an easily to follow diagram.
Remove the EGR valve.
Inspect the location of the carbon built-up inside the valve and the EGR passage tube.
SOAK these areas with WD-40 spary.
You will need a small screwdriver,cloth hanger and lot of newspaper and time to get this cleaning done right.
RE-SOAK the carbon and let it sit for over-night will also help.
One the last round,pass a shop vacuum of the EGR valve and the passage pipe.
Install the new EGR gasket and connectors.
Allow the vehicle to warm up outdoor to burn up any remaining WD-40.
Take it for a test drive.
Please rate my answer if it's useful to you.
Cheers,
Mustgo
SOURCE: Dodge Caravan Fuel Injectors gone bad?
if you can get a good set of used injectors you should change all of them.
179 views
Usually answered in minutes!
×