How do I Remove the Back seat In A 2003 Oldsmobile Alero?

SOURCE: 2001 olds alero rear seats

There shouls be 2 straps inside the trunk at the top. Both on the driver side but one is for the left side and one for the right side seats. Pulling on the straps releases the 'lock' that should then allow you to pull down the seats from the back seat area.

SOURCE: I cannot fold down seat

Try looking for a strap in your trunk it should be located at the upper inside of your trunk, there could be one or two straps, when you pull on these straps they act as a release lever for your rear seats, pull the straps toward you and push the seats forward from the trunk side.

SOURCE: 1999 intrigue rear speaker help

The lower seat cushion, the back seat rest, the side trim panels and the package shelf all have to be removed to access the rear speakers.

SOURCE: need to know if i

here are step by step instructions on the removal and installation of your fuel tank and fuel pump. please do not forget to rate and comment about your experience with fixya today.
Removal & Installation

1. Before servicing the vehicle, refer to the precautions section.
   
2. Relieve the fuel system pressure.
   
3. Drain the fuel tank.
   
4. Remove or disconnect the following:
   
5. While holding the modular fuel sender assembly down, remove the snapring, if equipped or if equipped with a cam lock ring use Fuel Sender Lock Nut Tool J-39765 to press down and rotate the cam lock ring to remove it.
   
   WARNING If the modular fuel sender assembly is retained by a snapring, it may spring up from its position. When removing the modular fuel sender from the tank, be aware that the reservoir bucket is full of fuel. It must be tipped slightly during removal to avoid damage to the float.
   
   • Fuel sender assembly
     
   • External fuel strainer
     
   • Connector retainer from the wiring harness and the fuel pump
     
6. Gently release the tabs on the sides of the fuel sender at the cover assembly. Begin by squeezing the sides of the reservoir and releasing the tab opposite the fuel level sensor. Move clockwise to release the second and third tab in the same manner.
   
7. Remove or disconnect the following:
   
   • Fuel pump electrical connection by lifting the cover assembly
     
   • Baffle and pump assembly from the retainer by rotating the fuel pump baffle counterclockwise
     
   • Fuel pump outlet by sliding it out of slot
     
   • Fuel pump outlet seal
     

1. • Fuel pump outlet with a new seal by sliding it in the reservoir cover slots
     
   • Fuel pump and baffle assembly onto the reservoir retainer by rotating it clockwise until seated
     
   • Lower retainer assembly partially into the reservoir by aligning all 3 sleeve tabs and pressing the retainer onto the reservoir making sure all 3 tabs are firmly seated
     
   
   NOTE Gently pull on the fuel pump reservoir to assure it is secure. If not secure, replace the entire fuel sender.
   
   • Connector retainer to the wiring harness and the fuel pump
     
   • External fuel strainer
     
   • Snapring, if equipped to the retainer slots while holding the modular fuel sender assembly down or use Fuel Sender Lock Nut Tool J-39765 in order to install the cam lock ring
     
   • Fuel tank
     
   • Negative battery cable
     
2. Pressurize the fuel system and verify no leaks.
   

SOURCE: We need to reset the computer on a 2003 Oldsmobile Alero

HI there if the scan tool you are using will not reprogram the theft module the try the 10 min relearn

1. Turn ON the ignition, with the engine OFF.
2. Attempt to start the engine, then release the key to ON (vehicle will not start).
3. Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.
4. Turn OFF the ignition, and wait 5 seconds.
5. The vehicle is now ready to relearn the Passlock™ Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK. Important: The vehicle learns the Passlock™ Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
   
6. Start the engine. The vehicle has now learned the Passlock™ Sensor Data Code and/or password.
7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles