2005 Acura TSX Logo

Related Topics:

A
Anonymous Posted on May 31, 2014

2005 Acura tsx hid problems

High beams work and passenger low beam only works intermittently. Replaced 1 ballast already and I don't know why the problem isn ow

5 Related Answers

Anonymous

  • 21 Answers
  • Posted on Aug 29, 2008

SOURCE: a/c won't work and there

Try the relay for the a/c problem.  Try the relays for the headlights also.  

Ad

Anonymous

  • 1 Answer
  • Posted on Feb 08, 2009

SOURCE: Low Bean Lights Inoperative on 1997 Acura TL

If your car is running daytime running light system .. there is a DTR relay that goes defective and needs replacing ... I had the identical problem that was fixed with this replacement. The DTR relay is behind the glovebox.

Michael Gutwein

  • 104 Answers
  • Posted on Feb 09, 2009

SOURCE: Right headlamp doesn't work on low beam only

in this case make sure you have voltage going to the low beam lights. 12 volts. you need a volt meter. if you do not have volatge you have to check and make sure power is going through the fuse. a bad fuse will be broke, but you can have a good fuse with no power going through it. if you have power going through the fuse you have a wiring open somewhere between fuse and whatever is between the headlight connecter.

plz check and get back i will keep checking on here on and off.

Michael
ASE certified
PLZ rate

Anonymous

  • 1 Answer
  • Posted on Mar 17, 2010

SOURCE: 2002 Acura RSX low beam headlights dont work. All

The same thing happended to my Acura RSX and now they are saying that it is an electrical problem. I put new bulbs and both of them are fused

Anonymous

  • 1 Answer
  • Posted on Feb 15, 2011

SOURCE: 2002 Acura TL low beam headlight

How to Shift my headlight beam from position.
from I replace my headlight it's spatting directly on the ground..What can i do to change it from position

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Headlights do not work high or low beam all other lights work

Re: Condensation in Sienna Right Headlight.... - Toyota Sienna Forum

www.siennachat.com/.../4606-condensation-sienna-right-headlight.html
Mar 10, 2009 - 15 posts - ‎9 authors Over the years, I was not a frequent visitor to SiennaClub...but when I did visit, it was... in the right, passenger-side xenon HID headlight of my 2004 Sienna...the light has... Check with your dealer and see if they can do anything about it. .... :o The HID bulb is also a PITA to remove because you are working ... Re: 2004 Sienna no brake lights, radio, heater/AC ...
15 posts
Jan 4, 2013
Thread: HELP: Both Low Beams don't Work
6 posts
Nov 27, 2011
Thread: 2000 sienna drl and/or headlight issue
5 posts
May 7, 2010
Automatic Headlight Option: Useful or Not?
8 posts
Mar 3, 2010
More results from www.siennachat.com

Toyota 2004 Sienna repair: Replacing HID ballast or ...

toyotarepairsemipro.blogspot.com/.../replacing-hid-ballast-or-computer....
May 1, 2010 - Replacing HID ballast or computer control lighting for the Headlight. Just got a ... Up until now, I did not know I had the option of seeing twice as far with Xenon. Also up to ... In the end after buttoning everything up, the light did work fine. .... Howdo you determine if you have a HID or non-HID light? Reply ...
0helpful
1answer

Headlamps not working.

is the light setup one ballast for high and low beam ? if so the ballast has gone, probably even the bulbs. replace the ballast and bulbs. some aftermarket ballasts don't last, if you cannot find the right ballast for replacement you will need to replace both ballasts. as every ballast set are set the same and sold in pairs.
1helpful
1answer

I have a 2003 Saturn Ion 1 and bought the xenon hid 9007/HB5 kit. Hid low beams and halogen high beams no bi-xenon bulbs. The high beams work but lows do not. Neither ballast seems to be getting any power?...

The Saturn ion wasn't meant to have H.I.D.installed in them.
Since you want to install these and blind everyone, check what you grounded the ballast to, you probably don't have them grounded properly.
0helpful
2answers
0helpful
1answer

How do i wire up hid headlights on 2005 mazda 3

To wire up an HID kit on the low beams of your Mazda 3 2005, you will need 3-4 things:
1- HID kit (bulbs and ballasts)
2- HID relay (connects your hid kit to your battery)
3- 4700uF capacitor (solves DRL flickering issue)
4- H7 hid bulb adaptor (you can also use the rubber piece that holds the bulb wires as a spacer)


Wiring diagram:
http://www.carsets.co.uk/upload/temp/images/hid-light-installation-photo-display.jpg

Tips on How to wire up:
1. HID bulb's amp wires connects with the ballast's amp wires. (There's only one way to connect them.)
2. The positive and the negative spade connectors from the hid relay connect with your vehicle's low beam connector, closest to your battery: the driver side. The passenger side low beam connector is not used and should be insulated. You can use electric tape.)
3. Each ballast is connected to one of the relay's clip connector, and it's grounded on each side to your vehicle's body. (One connector for each ballast, one for each side. You can use the screw for the body as a ground.)
4. The red wire(with the inline fuse) in the relay connects to your battery's positive terminal.
5. The capacitor sits on the relay switch. (Google for how to wire the capacitor onto the hid relay switch.) dynoxg image
6. The halogen bulb sits on an adapter. You can safely remove them from each other, and use an H7 hid adapter instead.

For more help: Moonlight Driving
5helpful
4answers

2004 Lincoln Navigator low beam headlight went out so I changed the bulb and fuse but it still does not work.

If you have the HID bulbs check with an Autoparts store like Autozone. I believe the right and left headlights have separate Relays in the Powerbox. It is possible that there are 2 low beam and 2 high beam relays total. They pull too much power for both sides to be wired together and may wire the high beams separate too!
0helpful
1answer

Low beam on passenger side is out. My 2002 Acura TL Low Beam light starting flickering and now it doesn't work at all. It's on the passengers side and I've got some outrageous quotes on fixing it. Light...

Sounds like it is an HID light system on there, you can get after market bulbs MUCH cheaper then from the dealer. and with the bulb flickering first, then dying, it sounds like a bulb issue, not the ballast.
let me know where you live, i might be able to point you in the right direction.
Not finding what you are looking for?

301 views

Ask a Question

Usually answered in minutes!

Top Acura Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...