Clark wakes it up
answer
there are 6 engines, used, in this car.
never ask how to work on any cars engine, without firsts
say, ah, my car is USA J20B engine.
or/ the other 5, some are diesel.
got a DTC error for it, what was it???
never work on a car, engine,
and not know what is there.
and the fail to say.
in most cases you will make it worse.
next time.
tell COUNTRY, be like the 4th ever.... shocking us to the core.
then year
then engine size. (displacement and cyl. count)
if in the USA say so. its that too hard. really>?
ill answer for J20b KS sensor.
ive posted photos of it here, many times
here we go 1 last time.
the 2nd photo was posted to fixya last year
http://www.fixya.com/cars/t25824772-anyo...
there you go, all 3 pages in the FSM
covering this topic,
if you read the FSM it is there, if you just read it.
J20B , KS is here, its a 1 wire, sensor
so that be unique, 1 wire.......
now my last year post is 2 more photos added.
j20b only.
part 15? , 12 in schematic.
usually the KS is bolted to the block side
central, to hear all 4 cylinders,its a microphone, and if mounted to a head, has to listen to huge, valve noise, so is a bad spot.
keep in mind , there are 6 engines
and many posts and many photos of wrong engine.
knowing the above,leaves only 2 places
dead center of block front and rear.
Transverse engine,
is this hard?, look both places for 1 wire.
do not pick the oil pressure sender.
on V engines, more tricky. but not In-line engines.
the 1 wire sensor red wire is IT./
no more guessing..
MY GUESS IS HERE. FRONT SIDE ABOVE FILTER
old posts but the only one with a photo
so why I answered.
the other engines are her, learn to know what engine is there first. then post
year, car engine size and country
and win, its a win-win,for you and for the guy not having to blind guess you.
1.5 L M15A I4 (petrol)
1.6 L M16A I4 (petrol)
2.0 L J20A I4 (petrol)
2.0 L J20B I4 (petrol)
1.3 L D13A I4 (diesel)
1.6 L DV6ATED4 I4 (diesel)
1.9 L D19A I4 (diesel)
2.0 L D20A I4 (diesel)
the KS is just microphone that listens to
combustion so needs to be near that is correct, at combustion and that is near upper cylinders, and best spot is center.
if you look close that is where it was this time.
×
Best Manuals
for the best solution of your problem visit this site
Posted by Anonymous on Jun 03, 2014
×
SOURCE: I'm trying to locate the spark plugs in my suzuki 2008 sx4.
You remove the rectangular plastic cover on top of the engine(2 screws), under that is the plug wires and spark plugs. Pull wires straight up, remove plugs with proper spark plug socket, extension and ratchet, reverse to install.
Platinum plugs are not required but will allow longer change intervals. Check the gap but do not gap them, if they are not properly gapped. Bring them back and asked for new ones.
The metal's on the Platium plugs are harder then copper plugs and can break upon trying or break in your cylinder when in uses.
Good luck and hope this helps
SOURCE: How often should i change my oil in a suzuki sx4
every 3000 miles or 3 months. You should change it before the light comes on. Unless you are using synthetic oil.
SOURCE: 2007 suzuki sx4 emission control light on. 17000 miles
My light in my 2007 SX4 just came on. Apparently my oxygen sensor is wrecked... allegedly from oil dropping on it during oil changes. Did the light come on after the most recent oil change?
SOURCE: where is the knock sensor located on my 08 suzuki sx4
The P0327 means Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor).
the knock sensor is located in the front of the engine located behind the oil dip stick just to the left.
_______________
Ktag K-TAG
SOURCE: keyless remote not working on my suzuki sx4
think it may be a new battery in key fob had same prob with mine and used other spare key and works fine now ..
1,526 views
Usually answered in minutes!
×