Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Jun 04, 2014

How much tourque on head bolts

1988 acura integra

1 Answer

Richard Conbere

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Prodigy:

An expert who has answered 500 questions.

  • Acura Expert 554 Answers
  • Posted on Jul 23, 2014
Richard Conbere
Acura Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Prodigy:

An expert who has answered 500 questions.

Joined: Aug 25, 2012
Answers
554
Questions
0
Helped
207040
Points
716

22 then 63 ftlb. Google this for torque pattern.

5 Related Answers

Anonymous

  • 702 Answers
  • Posted on Jul 13, 2008

SOURCE: threads to spark plug stuck

Spray a good penetrating oil at the base of the plug. I use PB Blaster. Slowly try working the plug loose. I like to start the engine and let run for a minute so the head gets hot and spray the lubricant and while the head is still warm, try to remove the stuck plug. By getting the head warm, it allows the aluminum to expand a little.

Ad

Curt Downs

  • 1779 Answers
  • Posted on Jan 15, 2009

SOURCE: acura integra engine torque specs

56 ft lbs torque main bearings, NON v-tech engine.

daniel timmons

  • 153 Answers
  • Posted on Oct 07, 2009

SOURCE: timing belt diagram fo 1990 acura Integra

78338863have fun

Anonymous

  • 86 Answers
  • Posted on Jan 09, 2010

SOURCE: how to change a starter on 92 acura integra RS

There are two bolts. One on top and one under the starter. It is best done by removing the rubber air intake tube and the battery. The bottom bolt is difficult but with a ratchet, socket and a couple of extensions it can be done. Disconnect the battery before disconnecting the wires to the starter.

Larry Chandler

  • 1149 Answers
  • Posted on Feb 03, 2010

SOURCE: need code for 1999 acura integra radio

Hi:

You have to go to your Integra dealer to get that, due to the fact it is an anti theft code. Of ten they also need the number off the top of the radio too.

This keeps thieves from selling stolen radios...

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

How to take off a rounded egr valve on my 1992 acura integra?

A good sharp chisel. you might try heating the nut up before trying to remove it. Make sure any exposed stud threads are clean, maybe soak it in penetrating lube.
1helpful
1answer

1988 Acura Integra error code My Acura has an

An error code 17 is the (VSS) Vehicle speed sensor.
Matt
0helpful
1answer

Im replace a head on a 1990 acura integra b18a engine can i reuse the same head bolts

no, always use new head bolts/head studs
Acura recommends this at every head gasket service unless previously replaced at last head gasket service....
I reccomend ARP head studs or equivalent quality
0helpful
1answer

What is the torque pattern for the head on a 96 acura integra gsr i already kno what ft. lbs they all are i just need to kno what pattern to torque them in

<P>all cylinder heads are the same start at the middle then work outwards like&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;11.9.3.1.6.8.14.</P><P>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 13.7.5.2.4.10.12.</P><P>start with 1/2 torque then 3/4 then full torque.then recheck ALL BOLTS after 250 miles.</P>
1helpful
1answer

Fix my powerhose for 1988 acura integra

Integras are known for igniter assembly failure. Depending on engine year and model may be located inside of distributor or on inner fender well.

Check for spark at spark plugs, if no spark and cap and rotor o.k. suspect igniter. If you have spark check for fuel pressure with test guage, if fuel present, check to see if injectors are firing. (noid light will prove this out). If injectors not firing suspect camshaft position sensor.

If no fuel pressure suspect fuel pump or clogged filter.

Good luck and do rate this solution.
2helpful
1answer

Show me a wireing diagram for the fuel pump on a 1988 acura integra.

If you go to Autozone.com and register for a free account, you can add your cars to an online garage and access free online manuals for them there. These have diagrams and electrical shematics, just like a Haynes.

Hope this helps,
matt
0helpful
3answers

1988 acura integra overheating

radiator replace or get rodded check radiator temp at top and bottom should be about 10deg differance
0helpful
1answer

Special bolt on the crankshaft pully on 1990 acura integra

It should be a hex bead bolt. Nothing really special about the. If its a bolt that is torqued then tightened to a specific angle then you need to replace it when doing the work.
Not finding what you are looking for?

74 views

Ask a Question

Usually answered in minutes!

Top Acura Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...