Likely problem? It sounds like you have a pinched power wire somewhere, cutting off power to the remote control receiver when the door is closed, I'd have the dealership check it out.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Here are the codes you posted along with the possible issues that may have caused each code to be triggered. It's possible the circuit these switches share has a problem that needs to be diagnosed.
It could well be a problem with the wiring or a problem with the connections between the switches and the Multiplex Control Unit, or possibly with the Multiplex Control Unit itself.
B1129
Driver Side Door Lock Knob Switch Signal Error
Faulty Driver Side Door Lock Knob Switch
Driver Side Door Lock Knob Switch harness is open or shorted
Driver Side Door Lock Knob Switch circuit poor electrical connection
Faulty Door Multiplex Control Unit
B2077
Right Power Sliding Door Remote Control Switch 1 Signal Error
Faulty Right Power Sliding Door Remote Control Switch 1
Right Power Sliding Door Remote Control Switch 1 harness is open or shorted
Right Power Sliding Door Remote Control Switch 1 circuit poor electrical connection
Faulty Right Power Sliding Door Control Unit
B2078
Right Power Sliding Door Remote Control Switch 2 Signal Error
Faulty Right Power Sliding Door Remote Control Switch 2
Right Power Sliding Door Remote Control Switch 2 harness is open or shorted
Right Power Sliding Door Remote Control Switch 2 circuit poor electrical connection Faulty Right Power Sliding Door Control Unit
B2079
Right Power Sliding Door Remote Control Switch 3 Signal Error
Faulty Right Power Sliding Door Remote Control Switch 3
Right Power Sliding Door Remote Control Switch 3 harness is open or shorted
Right Power Sliding Door Remote Control Switch 3 circuit poor electrical connection
If you pushed the car by the door itself or swung the door open hard, you could ha e stretched the door harness and pulled wires apart. There is a little accordian styled boot that 'protects, the wire loom leading to the driver door electronics. I wonder if you have noticed your alarm horn doesnt beep when locking the doors from the remote. Or you can only lock and unlock the driver door only from the driver door. If thats the case there may be an open in the wires leading to the door lock actuator; which controls things like lock/unlock functions of all doors and windows, door warning lights, etc. Have the harness repaired
Programming When Remote control added or replaced. System malfunction. How Obtain all remote controls. Remove key from ignition switch. Close all doors. Open driver's door. Carry out the following within 24 seconds: Turn ignition switch ON and back to LOCK position 3 times. Remove key. Press and release driver's door courtesy light switch 3 times. Ensure doors lock and unlock. If not, wait 40 seconds and repeat procedure starting with driver's door already open. Press each remote control lock or unlock button twice. Ensure doors lock and unlock after each remote control operation. If not, proceed as follows: Press and release driver's door courtesy light switch once. Ensure doors lock and unlock twice. Repeat procedure starting with driver's door already open. NOTE: A maximum of 3 remote controls can be programmed.
Get into your passport and unlock all doors. Leave drivers door open. Put key into ignition. Turn to ON (not start), then OFF three times within 5 seconds. Close and open the drivers door twice. Turn key to ON then OFF 5 times within 5 seconds. Close then open the drivers door. Press either the lock or unlock button on the remote. Doors will lock then unlock. Press the button again. Doors will lock then unlock again. Close door to finish programming. If it doesnt work, try it again but turn the key faster. You have to do it all pretty quick, but I had it done on the second try.
1. sitting in driver seat, with driver's door OPEN, press lock/unlock
button ON THE DRIVERS DOOR to lock all doors, then manually unlock
driver door only. 2. Insert YOUR key in ignition, DO NOT TURN, then remove key. 3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles 4. Shut door. 5. Open door. 6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles 7.
With the door open insert your key into the ignition, turn to 'on'
position (DON'T START), wait 5 seconds. Turn off and remove key. 8.
Locks should cycle once (Car will lock and then unlock once by
herself). If they don't cycle or they cycle more than once, do steps
1-7 over. 9. Now using the remote, push lock button, hold for one
second, then release the button. The locks should cycle once. If not,
start over and go slower. 10. Close the door. 11. Open the door. 12. Press the lock button on the remote. The locks should do a lock-unlock cycle. 13. Close the door 14. Press the lock button on the remote, the doors should lock. 15. Press unlock button and the doors should unlock.
1. sitting in driver seat, with driver's door OPEN, press lock/unlock
button ON THE DRIVERS DOOR to lock all doors, then manually unlock
driver door only. 2. Insert YOUR key in ignition, DO NOT TURN, then remove key. 3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles 4. Shut door. 5. Open door. 6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles 7.
With the door open insert your key into the ignition, turn to 'on'
position (DON'T START), wait 5 seconds. Turn off and remove key. 8.
Locks should cycle once (Car will lock and then unlock once by
herself). If they don't cycle or they cycle more than once, do steps
1-7 over. 9. Now using the remote, push lock button, hold for one
second, then release the button. The locks should cycle once. If not,
start over and go slower. 10. Close the door. 11. Open the door. 12. Press the lock button on the remote. The locks should do a lock-unlock cycle. 13. Close the door 14. Press the lock button on the remote, the doors should lock. 15. Press unlock button and the doors should unlock.
×