How do i install side glass?

you take off the door panel by using a panel clip tool to pop the clips for the panel to come off also check for any screws holding the panel to the door by the inside door handle the bottoms of the panel once you get it off unplug the window door switches to move the panel out of the way but first lower the window track so you can see it remove the weather seal plastic and then when you can get to the track and the glass you'll see that there should be yellow circle clips that pop together to hold the glass with rivets I'm assuming the glass is broken and this might have come off and is in the bottom of the door use these for the new glass after drilling out the old rivets snap them together one on each side of the new glass and then put bolts and nuts on to tighten or use a rivet gun to the track reconnect the switches for door window power and raise the glass

The window track should have a bolt at the bottom so the track can be moved away from the window to allow enough room to slip it in between the tracks.Also the door skin can be unbolted to gain access from the outside of the door which may make it easier.

remove interior door panel inside you will see where it mounts to should be two to three bolts and possible a clip that holds it in place remove old glass and install new glass from top of door remount into window gear mechanisim

REMOVAL

1. Remove the watershield. (Refer to 23 - BODY/DOOR - FRONT/WATERSHIELD - REMOVAL)

2. Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent(FRONT DOOR GLASS CLIPS).

3. Disconnect wire connector from power window motor, if equipped.

4. Loosen screws attaching front and rear window guide rails to inner door panel (FRONT DOOR MANUAL WINDOW REGULATOR - TYPICAL).

5. Remove screw heads on guide rails from key hole slots in inner door panel.

6. Loosen screws attaching regulator to inner door panel.

7. Remove regulator from inner door panel.

8. Extract rear guide rail through inner door panel rear access hole (FRONT DOOR POWER WINDOW - TYPICAL).

9. Extract front guide rail through front access hole.

INSTALLATION

1. Insert front guide rail through front access hole.

2. Insert rear guide rail through rear access hole.

3. Place window regulator in position on inner door panel.

4. Place screw heads on guide rails in position through key hole slots in inner door panel.

5. Tighten screws to attach front and rear guide rails to inner door panel.

6. Connect wire connector into power window motor, if equipped.

7. Install door glass.

8. Verify door glass alignment and operation.

9. Install sound shield and door trim panel

DIAGRAMS CAN BE FOUND ON JUSTANSWER,COM

one screw at handle two on arm rest or under switch the rest is plastic retainers just putt and use trim tool or screw driver two bolts hold glass to regulator have to lower window till you see then remove remove bolt that holds front track and slide glass in top and put in track front an back set in regulator and bolt in raise then bolt front track

WINDOW GLASS REMOVAL

NOTE: Window glass must be operable in order to remove door assembly carrier. Any malfunction that prevents the window (manual or power) from being lowered must be corrected before proceeding.

• Remove door trim panel.
• Pry out sealing plugs in door assembly carrier to gain access to window glass securing bolts.
• Lower window until window glass securing bolts are accessible.

NOTE:
If the power window motor is not working it can be renmoved to allow the window to be slid down.

• Loosen window glass securing bolts and carefully press glass securing clamps apart.

NOTE:
If glass is being replaced due to breakage, remove door assembly carrier and remove broken shards of glass to prevent rattling noises in door.

• Carefully lower the window regulator.
• Lift window glass up and pivot forward, starting at the taller end of the glass. Pivot forward towards the direction of the side mirror.
• Place removed window glass in a secure location.

WINDOW GLASS INSTALLATION

• Slide forward part of window glass into opening and pivot glass downward, reversing the removal proceedure.
• Raise window regulator until window glass securing bolts are visible in access holes on door assembly carrier.
• Gently press window in the direction of the door latch or highest part of glass and tighten securing clamp bolts.
• Remainder of installation is the reverse of disassembly.
• Check operation of window before final installation of door trim panel.

TIGHTENING TORQUE
Window glass securing bolts...........10Nm (89in-lb)

sounds like the track has been dismounted....try to pull off the inside door panel and look for any missing or broken bolts on the track itself... the track protrudes down to keep the window on track....if this is not a problem look at the glass itself...roll the window down a little to see the bottom of the glass. makes sure all of the mounting brackets are in place and secure..

probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal

1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
   

1. CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
   Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .
   
   
   
   
   

1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
   

1. Pull the shop rag back and forth to release the window regulator handle clip.
   
   
   
   
   

1. Remove the three cover caps and front door trim panel screws.
   

1. Remove the one front door trim panel capped screws from the door pull handle.
   

1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
   

1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
   

1. Remove the front door trim panel.
   

Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal

1. Disconnect the battery ground cable (14301) .
   

1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
   

1. Remove the two front door brace bolts and the front door brace.
   
   
   
   
   

1. Disconnect the front window regulator electric drive electrical connector.
   

1. Remove the four front door window glass regulator track bolts.
   
   
   
   
   

1. Remove the three front window regulator electric drive bolts.
   

1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
   

Installation

1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
   

1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
   

1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.
   

are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

1. Remove the front door trim panel; refer to Section 501-05 .
2. go to car-part.com for a used mirror. Page with * is cheapest seller.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

------------------------------------------------------

----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors

1. Position the glass in the full up position.

1. Locate the notch at the bottom of the exterior mirror glass.

1. Release the exterior mirror glass.
   1. Insert a long flat-bladed screwdriver in the notch.
   1. Push the screwdriver into the notch until the glass is released.

Heated mirrors

1. Position aside the exterior mirror glass.

1. Disconnect the electrical connectors.

All mirrors

1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.

Installation
Heated mirrors

1. Connect the electrical connectors.

All mirrors

1. Position the exterior mirror glass on the exterior mirror motor.

1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

My 97 Grand Prix sunroof tracks are offset. My driver side track is in the closed position, and the passenger side track is in a half open position. When the problem happened I was closing the roof and heard a hard clicking. It stopped working from that moment on. The tracks werent offset as much as they are now before I took the glass off. When I removed the glass, the passenger side track sprung back about 6 inches. The motor works, but the tracks only move about a half inch forward and backwards. Its cable operated and my guess is that one side jumped the track or a gear or something. Anybody help?