Question about 2000 Chevrolet Silverado 1500

Open Question

Re-programming key fob on 2002 silverado 1500

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 135 Answers

SOURCE: program fob

Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.

  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Posted on Apr 20, 2009

Ad
blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: program a new key fob for a 2002 chevy tahoe

1. Close all vehicle doors.



2. Insert the key into the ignition.


3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.



4. Perform steps 5 through 8 in fairly rapid succession.


5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).



6. Turn the ignition switch to the OFF position.


7. Turn the ignition switch to the ON position.


8. Turn the ignition switch to the OFF position.


9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.



10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.



11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).



12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.




Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 27, 2009

rogrrabbit

Roger Campbell

  • 986 Answers

SOURCE: how to program key fob. I have the fobs.

Transmitter Programming Procedure
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on the transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of the transmitter.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Good luck

Posted on Jun 25, 2009

Molson02536

Harvey N Tawatao

  • 3854 Answers

SOURCE: 1999 Chevy silverado z71trying to program a new key fob

Use this procedure for New Body Style.
1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).




Posted on Apr 29, 2010

jsmes1027

Jonathan S

  • 749 Answers

SOURCE: Do I need to reprogram all of the key fobs for my

All key fabs need to be programmed at one time.


Method 1 - No Tools Required, Program All Transmitters
Important: All transmitters which are to be recognized by the PDM must be programmed in a single programming sequence. When using this program method, all previously programmed transmitters will be erased upon the receipt of the programming signal from the first transmitter.
The order in which the transmitters are programmed will determine its numbering position within the PDM memory. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. The number stamped on the transmitter case is for reference only; #2 can be programmed as #1, or vice versa. Additional unnumbered transmitters are also available.


  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the door unlock switch.
  4. While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to 4 transmitters.
  8. Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter programming mode.
  9. Operate the transmitter functions in order to verify correct system operation.

Posted on Nov 25, 2010

Testimonial: "This was more help than what I was getting from the dealership that lost the fob in the first place. They wouldn't tell me how to program them. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Programming key fobs for a 2007 Silverado


If Your 2007-2010 Silverado Has a VIC - Vehicle Information Center Step 1: Sit in the vehicle with all the doors closed and unlocked. Start your Silverado and leave it in Park.
Step 2: Press and hold the Vehicle Information button, marked by an image of a car and the letter "i", until the display reads "Press V to Relearn Remote Key".
Step 3: Press the Set/Reset button until "Remote Key Learning Active" appears.
Step 4: Simultaneously press and hold the Lock and Unlock buttons for 15 seconds. A chime will sound indicating the remote has been successfully programmed.
Step 5: Program additional remotes by repeating Step 4 for each fob.
Step 6: Exit programming mode by turning off the vehicle and removing the key.
Step 7: Test your remote(s).
If Your 2007-2010 Silverado Doesn't Have a VIC - Vehicle Information System Step 1: Sit in the vehicle with all the doors closed and unlocked. Turn the key to Accessory Power position.
Step 2: Press the trip odometer meter reset stem repeatedly until you see "Relearn Remote Key".
Step 3: Press and hold the trip odometer meter stem for three seconds. The display will read "Key Learning Active".
Step 4: Simultaneously press and hold the Lock and Unlock buttons for 15 seconds. A chime will sound indicating the remote has been successfully programmed.
Step 5: Program additional remotes by repeating Step 4 for each fob.
Step 6: Exit programming mode by turning off the vehicle and removing the key.
Step 7: Test your remote(s).

Nov 02, 2016 | Chevrolet Silverado Cars & Trucks

1 Answer

Key fob dont work, but door lock works ok, key fob battery change.


1. Get in your vehicle.
2. Close the door.
3. Put key in ignition
4. Do not turn on the ignition yet.
5. Hold down on the unlock button on the door panel. Do not let up.
6. Turn the key to ON, OFF, ON, OFF (while still holding the unlock button on the door panel).
7. Release the unlock button.
8. The door locks should cycle, indicating that you did everything correctly.
9. Have all your remote entry fobs available. Hold down on both the lock and unlock buttons until the door locks cycle. Do the same on all key fobs. This will re-program all of them.
10. Turn ON the ignition key to exit the program mode.
11. DONE.

Apr 18, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

2002 silverado single cab,haveing trouble getting into programe mode for key fob programe.


this is a fairly simple fix, you will use a method called 3-10's:
step 1 is to turn key on engine off.
step 2 is turn key to start briefly then let off (maybe a second and then just let off key)
step 3 remain inside vehicle do not touch anything for approx. 10 mins. then on your message board the security will quit blinking .
step 4 at this time you will turn the key off for FIVE mins. and turn back on.
repeat step 1-4 TWO more times, after this time you can turn the key off once again and your done the next time you cycle the key, the fob should be programmed to your computer. good luck

Mar 07, 2010 | 2002 Chevrolet Silverado 1500

1 Answer

Keys stuck in 2002 Chevy Silverado 1500.


Might work!!!! get under the front end and try to pull the bonnet release cable when open take the live off the battery and keep arking it off the battery may open the doors if central locking.

Jan 13, 2010 | 2002 Chevrolet Silverado 1500

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2002 montana program key fob


Key fobs tend to hold their code indefintely. The batteries in them are probably burnt. Open up one of the fobs and replace the battery (hearing aid type) then they should work fine. Good Luck!~

Nov 08, 2008 | 2002 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...