Question about 2008 Mitsubishi Lancer GTS CVT Sedan

Open Question

Brake rotor minimum thickness for 2008 mitsubishi lancer

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 6 Answers

SOURCE: Lancer IPod connect cord

I own a 2007 Eclipse.
You can purchase the cord from the dealership, with the instructions for the I-Pod cord. Not hard to install on the Eclipse, takes about 30 minutes to install. This is the only known place to get this I-Pod connector.

Posted on Feb 18, 2009

Ad

Kieran Donahue

  • 9 Answers

SOURCE: Which is the tensioner pulley on the 2008

Its usually the one with the 3/8" square hole in it.

Posted on Feb 20, 2010

Testimonial: "Perfect. Thank you!"

Anonymous

  • 12 Answers

SOURCE: need to find front end alignment specs for 2008 mitsubishi lancer

Unless your a front in alignment pro, take your car to a specialist, spend the $50.00 or so and have the front end aligned properly. If you're thinking of aligning your front end on your own, don't Normally this is not somehting that you can do without proper alignment equipment. If you have to have it, check an alignment shop ot ask the dealer.

Posted on Apr 23, 2010

Autotroubles

Sam Akber

  • 1105 Answers

SOURCE: OBD Indicator lights on in

There could be 22 diffrent problems, take it to any parts place and they will scan it for you.

Posted on May 02, 2011

heimlich

David Belcher

  • 1978 Answers

SOURCE: how to turn off the

Go to the local auto store where they will read the codes in your car for free. The diagnosis will tell you if you have any problems and what they are. After the diagnoses, before the reader is unhooked from the car, the parts employee reading the codes can push a button and turn off the light. you will find out if the car is in need and you will get the light turned off. If there is a problem , and you do not fix it, the light will probably just turn back on again. With a car that new you probably just have a dirty EGR exhaust gas recycling valve that needs to be cleaned. It is usually located on the throttle body and is easily accessed by removing the air intake tube from the air cleaner to the throttle body.

Posted on Aug 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Minimum rotor thickness for 2008 mkx front and rear


Look on back side of rotor and minimum thickness should be shown.

Sep 29, 2016 | 2008 Lincoln MKX

1 Answer

Brake disc limit


The minimum rotor thickness is normally cast into the rotor. You will find it printed either on the outside hat section of the rotor or on the very top edge section of the rotor.
There are some example pictures here

http://forums.justcommodores.com.au/dba-brakes/249789-dba-tech-talk-when-your-rotors-undersize-rotor-minimum-thickness.html

Apr 19, 2016 | Cars & Trucks

1 Answer

Minimum thickness for buick lesabre front rotors


Hello there
From a kind chap on this page
http://buickforums.com/forums/threads/18395-Service-limits-for-brake-rotors

For a 2000 Buick LeSabre

FRONT BRAKE ROTORS:

Discard Thickness30.7 mm (1.209 in.)
Lateral Runout (New)0.06 mm (0.002 in.)
Minimum Thickness after Refinish31.08 mm (1.224 in.)
Rotor Diameter 15 inch Wheels (New)278.0 mm (10.9 in.)
Rotor Diameter 16 inch Wheels (New)303.0 mm (11.9 in.)
Rotor Thickness (New)32.20 mm (1.267 in.)
Thickness Variation (New)0.025 mm (0.001 in.)

Sep 15, 2014 | Buick LeSabre Cars & Trucks

1 Answer

Minimum rotor thickness


Call any auto parts store and they can look it up and tell you

Jul 15, 2014 | 2008 Chevrolet Silverado 1500 2WD

1 Answer

Avalanche minimum rotor thickness


Rear Brakes JC5/JH5 Utility Only
Rotor Discard Thickness* .............................. 28.50 mm (1.122 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 29.0 mm (1.142 inch)
Rotor Thickness-new .................................... 30.0 mm (1.181 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

Rear Brakes JH6
Rotor Discard Thickness * ............................. 27.50 mm (1.082 inch)
Rotor Minimum Allowable Thickness After Refinish ....... 28.0 mm (1.102 inch)
Rotor Thickness-new .................................... 29.0 mm (1.141 inch)
Rotor Maximum Allowable Lateral Runout ................. 0.05 mm (0.002 inch)
Rotor Maximum Allowable Scoring ........................ 1.50 mm (0.059 inch)
Rotor Maximum Allowable Thickness Variation ........... 0.025 mm (0.001 inch)

Nov 12, 2013 | 2002 Chevrolet Avalanche

1 Answer

What is minimum brake rotor thickness for the front and the rear?


All are different, on the back side of the brake rotor , will have a stamp with (MIN) and some number after it the will be the minimum spec thickness for the brake rotor.

Dec 02, 2010 | 2007 Chevrolet TrailBlazer SS

1 Answer

2003 sierra rear brake rotors


there is many kind of brake system of ur truck here i will send u everything about the brake and i hope its help

Rear Brakes JC3

Rotor Discard Thickness* 18.50 mm/0.728 in Rotor Minimum Allowable Thickness After Refinish 19.0 mm/0.748 in Rotor Thickness (new) 20.0 mm/0.787 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JC4

Rotor Discard Thickness* 28.50 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring1 .50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH2

Rotor Discard Thickness* 28.50 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH6

Rotor Discard Thickness* 27.50 mm/1.082 in Rotor Minimum Allowable Thickness After Refinish 28.0 mm/1.102 in Rotor Thickness (new) 29.0 mm/1.141 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
Rear Brakes JH7

Rotor Discard Thickness* 28.5 mm/1.122 in Rotor Minimum Allowable Thickness After Refinish 29.0 mm/1.142 in Rotor Thickness (new) 30.0 mm/1.181 in Rotor Maximum Allowable Lateral Runout 0.05 mm/0.002 in Rotor Maximum Allowable Scoring 1.50 mm/0.059 in Rotor Maximum Allowable Thickness Variation 0.025 mm/0.001 in
* All brake rotors have a discard dimension cast into them. Replace any rotor that does not meet this Specification. After refinishing the rotor, replace any rotor that does not meet the minimum or discard thickness specifications.

Mar 15, 2009 | 2003 GMC Sierra 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...