Question about 2007 Ford Edge SEL Plus

Open Question

How to remove headrest 2010 edge - 2007 Ford Edge SEL Plus

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove rear headrests from Wrangler unlimited


THERE IS A RELEASE BUTTON THAT YOU HAVE TO HOLD IN THEN JUST LIFT UP ON THE HEADREST

Aug 10, 2014 | 2010 Jeep Wrangler Unlimited

1 Answer

Remove headrest


hello,yes there is a 'button' on the bottom outer edge,that you simply press in[sometimes need to exert a bit more force] and keeping that pressed in,you then slide the whole head rest out. hope this helps, cheers

Apr 12, 2014 | 1981 Ford Escort

1 Answer

Remove headrests


There is normally a push button for adjusting the headrest height. This is the same button that you use to get it off. Sometimes they pull instead of push but you have to do it while pulling the headrest.

Apr 09, 2014 | 2010 Dodge Challenger

1 Answer

How to remove headrests on 2010 grand caravan


lift the head rest there is a tad that the head rest slide in squeeze the tad and pull up on the head rest.

Sep 19, 2012 | 2010 Dodge Grand Caravan

2 Answers

Remove 2012 headrest malibu


I have a 2012 malibu and looked this same thing up because I just put on a seat cover, on the driver's side head rest, looking at it from the back seat on the driver's side, there's the normal looking latch that let's you adjust the headrest down, but on the right side you'll see a little indentation in the plastic that you can also push down and if you press both at the same time, you can remove the headrest.
4_1_2019_3_20_57_am.jpg

Apr 27, 2012 | Chevrolet Malibu Cars & Trucks

1 Answer

How do i raise and lower the headrests on 2010 chrysler town and country


You should find a small plastic tab at the base of the headrest. If the headrest is down, you will have to force your hand under it and feel for it - it is fitted on one of the rods that the headrest rides up and down on. Once you find it, push on it as you pull the headrest up.

Aug 08, 2011 | 2010 Chrysler Town and Country

1 Answer

I need to remove a headrest so that I can install a child's safety seat. The seat is too high with the headrest on. How can I do that?


I have a 2010 Santa Fe and this is how I did it. Remove the back panel of the seat, there are 5 or 6 plastic clips that hold the seat back cover on, start at the bottom of the seat back panel and work your way upwards, pull the panel downwards and it should come off. Once the panel is removed, You will see a black cable running down the back of the seat. At the bottom of the cable, you will see a black plastic box with two clips holding it shut. Open the cover and pull away the cable from the box on the side that runs up to the headrest, once it releases the cable, remove the cable end from the holder inside. From there, just hold the headrest adjustment lock in and push upwards hard until it comes out with the cable.

Dec 13, 2010 | 2010 Hyundai Santa Fe

4 Answers

Can the headrest for a 2010 ford expedition be replaced with an aftermarket so not to have that angle?


I know five (5) people who purchased the 2009 or 2010 Expedition. All 100% of them have complaints of the headrest hurting their neck. I know folks that won't even drive their new 2010 Expedition because it hurts their necks, and the dealer won't take it back! If enough people tell ford about the problem, erhaps Ford will post a Technical Service Bulletin (TSB) to tell dealers how to fix the problem. It is possible to build safe headrests that do not hurt necks during normal driving: just look at the competition. The headrest is not the right equipment to sacrifice comfort. Neck pain causes distraction and is a safety issue. Ford should be as concerned about liability from wrecks caused by headrest pian distractions as they are about the rear impact safety. Complain to Ford!

Dec 11, 2009 | 2009 Ford Focus

2 Answers

Front Headrests


There is a plastic cover, about 1 1/8" diameter, on the base of the post on each side. You can remove it with a screw driver by carefully prising upwards at the edge. They just clip down.
Once these are lifted away from the seat, you will see the wire clip that locks the headrest into the seat. Remove the clip on each post, and you can then remove the headrest.
Reassembly is the reverse.

Feb 12, 2009 | 1992 Audi 80

Not finding what you are looking for?
2007 Ford Edge SEL Plus Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...