2001 Jeep Grand Cherokee Logo

Related Topics:

A
Anonymous Posted on Jun 26, 2014

What can i use to fix a noisy lifter in a 2001 jeep grand cherokee

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on May 01, 2009

SOURCE: window motor replace 2001 jeep grand cherokee

You need to remove all the skrews from the door. Normaly there is one in the handle of the door, one behind the in door lach handel and one under the bump out for the arm rest on the door. Than you need to take a flat head skrew driver slowly priying the panel off. There are plastic clips on the backside of the panel it is ok if you brake a few.

Ad

Anonymous

  • 3600 Answers
  • Posted on Nov 16, 2009

SOURCE: average cost to replace lifters on a 2002 jeep

depending all that is done about $300 dollars thats 12 lifters test 12 push rods replase rods $4.00 each rocker arm cover gasket oil filter and oil change afterwords. This does not include any replacement of oil pump or flushing which may be required, also would recommend a top engine clean before doing lifter replacement so when you change the oil once.

Anonymous

  • 136 Answers
  • Posted on Nov 28, 2009

SOURCE: Changing spark plug wires on 2001 Jeep Grand cherokee

yah direct ignition coil pack does away for the need a a distributer cap and rotor.much higher energy ignition system where the computer tell when to fire.if that helps.not hard to change.as long as you change them one at a time so you don't screw up the order.

Anonymous

  • 6982 Answers
  • Posted on Dec 10, 2009

SOURCE: 2001 Jeep grand cherokee motor knock 4.7 motor

First, if the noise is from the upper part of the engine and is more of a tapping than a knock, likely you have a problem in the valvetrain, most often a bad lifter or worn rocker arm. If the noise is low, deep inside, the noise is from a bearing. This is generally accompanied by lower than normal oil pressure. Regardless of the underlying cause, correcting the cause will not stop the knock. To do that correctly, the engine needs to be removed and all crankshaft bearings and the crankshaft itself need to be replaced (crank can sometimes be "undercut" and thicker bearing shells can be used depending upon the amount of wear.) If caught very early, sometimes only one bearing can be replaced in-car, but in 99% of all cases I have ever seen, most will fail again, sometimes more severely if done this way.

Testimonial: "Thanks"

Anonymous

  • 6982 Answers
  • Posted on Jan 25, 2010

SOURCE: I have 2001 Jeep Grand Cherokee Laredo and it is leaking coolant

Front drivers side could be a bad cap, lower hose or the radiator itself. You need to look carefully and find the leak source. Steam travels and isn't a good indication of where the actual leak is coolant will run down and take any path it can to reach the ground. Therefore, you need to follow it back to where it is coming from, then deal with it. Your water pump can also leak and run down the lower hose. there is a small hole in the pump behind the pulley. If you see coolant coming from there the pump needs to be replaced. Sealers will not work on hoses or pump leaks so don't bother using them for that.
Good luck...don't forget this is free, so rate answers!
I will answer follow-up questions too!

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Cost 1998 jeep grand Cherokee lifters knocking

There is a reason he is an "ex." Letting ex use your vehicle is asking for trouble. He gets i a wreck, it's on you. He blows up your engine, it's on you. Those noisy lifters means 2 things. Lifters need adjusting and it's being run low on oil. Good luck.
0helpful
1answer

Stop noisy engine lifters

No real fix for that

You can try the yellow bottle from solder seal
that says something about lifters

Change the oil & go with Mobil 1 full syn 5W-20
or 30 & mystery oil

Your only adding solvents to not much avail
0helpful
1answer

2001 jeep ran hot and cot off and was not registering hot and now lifter is tapping

Hi here is a quick fix for the lifter tapping. Try adding 4 Oz. of tramsmission fluid to the motor oil , and run the engine for two minutes at 1500 RPM. This should quiet the lifter tapping.It works everytime i come across this problem.
1helpful
1answer

When putting head back on after head gasket job, how do i set valves on 2001 jeep cherokee 4.0.

Valve Lash (Clearance) Adjustment

Print

These engines are equipped with hydraulic valve lifters. No valve clearance adjustments are necessary.Here's a link to help.

0helpful
1answer

My jeep has a knocking sound coming from the engine and makes the same clicking/knocking sound when I'm accelerating what could this problem be?

noisy lifters, or piston slap, i just had one where the piston went through the block, try on your next oil change putting a liter of tranny fluid in it with the oil, the better lubrication will settle a noisy rocker
1helpful
1answer

How to set rocker arms on 1995 jeep cherokee 2.5

The rockers on the 2.5 motor are hydraulic lifters.They cant be adjusted.If there is a noisy lifter it may be a different problem.What's happening?Hope this helps
1helpful
1answer

Lifter tapping

Yes, you can have just a lifter replaced, but it could be other parts as well...like a valve, rocker, or cam shaft. The valve cover needs to come off for a better inspection.
0helpful
1answer

Noisy engine

sounds like you may have a rod going out on the truck...
Not finding what you are looking for?

249 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...