How to remove the radiator from a 1999 pontiac grand prix
SOURCE: how to remove door panel off 2004 pontiac grand
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. Then pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything.
SOURCE: how do i remove the front seats of a 1998 Pontiac
On W-Body vehicles, the front seats are secured to the floorpan by
two front hook attachments and two rear bolts installed to nuts welded
to the floorpan.
The manually operated two-way front adjusters
provides only fore and aft movement of the seat. When the seat adjuster
handle located on the front seat is pulled up, the seat adjusters
unlock, permitting travel of the seat. When the seat is in the desired
position and the seat adjuster handle is released, the seat locks in
place.
A power operated six-way seat adjuster is available. The
adjusters are activated by three 12 volt, reversible, permanent magnet
motors with a built-in circuit breaker. The motors are energized by a
switch bolted on the seat side panel.
The three motors drive the
front seat and rear vertical actuators and a horizontal actuator. When
the adjusters reach the limit of travel, torque is absorbed through the
rubber mounted grommets located between the motor and the support. An
overload relay is provided in the circuit and will open should
excessive stall be applied.
The optional 60/40 split bench front
seats have seat back head restraints on the driver's and passenger's
seat back. The head restraints are designed so they cannot be removed
from the seat back without first inserting a small rounded tool inside
the head restraint support tube to release the locking tab. The 60/40
split bench seat is equipped with a reclining mechanism on both the
driver's and passenger's side. The recliner lever is located on the
outboard side of the spring cushion. When the lever is pulled upward,
the spring loaded dual linear reclining unit located in the cushion
frame is released, allowing the seat back to be pushed rearward or
allowing the spring loaded reclining unit to bring the seat back
forward.
Bucket seats are equipped with manual reclining
mechanisms. An optional six-way power seat adjuster is available. Some
bucket seats are equipped with inertia seat back locks. This system
allows the seat back to fold forward without requiring the occupant to
release a locking lever or access to the rear seat area. During a
sudden stop or deceleration, or if the front of the vehicle is nose
down, the inertia system of the seat back lock will engage, holding the
seat back in its rest position. A release lever is provided to allow
manual release of the seat back lock when the vehicle is in the nose
down position. The release lever is located at the lower rear outboard
corner of the seat back.
Some W-Body vehicles (notably Pontiac
coupes) have passenger front seats equipped with an E-Z Entry device.
This is actuated, in an unoccupied seat, by completely folding the seat
back forward disengaging the adjuster, and sliding the front seat
forward to gain access to the rear seat area. To return the seat to its
normal position, return the seat back to its rest position, and slide
the entire seat rearward, engaging the adjuster.
W-Body rear seats are available in several styles including a rear seat with an integral child restraint device.
SOURCE: remove shifter knob 1998 pontiac grand prix
Hello! It's best to put the gear shifter all the way back into the 1st gear. After you do this look on the front of the shift knob, just above where it meets the shifter's shaft you will see a horizontal slot - inside this is a clip. You will need a small flat-bladed screwdriver, or a mechanic's pick to pull this clip out, but once it is removed the shift knob will come off by pulling it straight up.
Thanks for using FixYa!
SOURCE: diagram on a pontiac grand prix
I have 07 Pontiac Grand Prix, the wrong key was inserted into the ignition the other day. Now when I try to use the correct key it will not insert completly in the ignition, goes in until last 1/4in of key. Im stuck, I bought the new lock cylinder but how do I get the old one out? I cant get the key to insert all the way so I cant get it to the "On" position, it will not turn at all. The key that was inserted in error is whole and nothing is missing it seems like there is something stuck. Any help would be appreciated...
SOURCE: How to Replace the Starter in a 1999 Pontiac Grand
starter is located on the engine block down below.
Removal & Installation
To Remove:
Before servicing the vehicle, refer to the precautions in the beginning of this section.
To Install:
Starter removal/installation – 3.1L & 3.4L engines
Starter removal/installation -3.8L engine
31 views
Usually answered in minutes!
×