SOURCE: Sensor "A" Error Messages
I would suggest replacement of your camshaft sensor as the first line of action, of course check your wiring and connectors first by unplugging them and plugging them back in.I will be glad to help you further if this doesn't solve your problem!
SOURCE: 1996 Dodge Intrepid camshaft position sensor circuit malfunction
DO U UNDERSTAND THE MEANING OF "OUT OF PHASE"?? IT IS THE MECHANICAL TIMING OF THE SIGNAL FROM EACH SENSOR TO THE ENGINE CONTROL COMPUTER, WHAT IS THE CODE? ALSO TELL YOUR DAD (NICELY) THAT ATROUBLE CODE DOES NOT ALWAYS MEANS A FAILED SENSOR, ONLY A PROBLEM WITH THE SIGNAL, THAT CAN BE THE WIRING, IT CAN BE MECHANICAL OR IT CAN BE THE SENSOR, MANY POEPLE DON'T GET THAT AND SPEND TON'S OF MONEY CHASING CODES.I HAVE DONE THIS FOR 35 YEARS AND AM SURE OF WHAT I AM SAYING 100%
SOURCE: 2002 Interpid 2.7 L died on road now no start!
sounds like a bad ecm aka computer to me.have ecm checked
SOURCE: Diagnostic code P 340 and P 341 Camshaft Position
The Camshaft Position Sensor tells the PCM (computer) the position of the Camshaft Position. This Sensor sychronized along with several other Sensors including the Crankshaft Position Sensor the firing of the electronics to the spark plugs of each cylinder.
It is not difficult to replace and relatively inexpensive.
1. Disconnect the Negative side of the Battery,
2. Locate the Sensor and unplug.
3. Remove the Position Sensor retaining bolt.
4. Pull out the Sensor.
Replacement is reverse of above order.
Hint: use fresh engine oil on the end/sides of the Sensor especially around the rubber o-ring(s) to ease pushing the Sensor into proper position.
SOURCE: code reads P0340 Camshaft position Sensor circuit
That makes the computor think the timing is off. Replace the sensor and see if that does it. You will then have to have the code cleared (erased) or the light will come back on/stay on.
?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.
DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1
DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1
DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2
DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2
DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1
DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1
DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1
DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1
DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2
DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2
DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1
DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1
DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1
DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2
DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2
DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1
DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1
DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1
DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2
DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2
DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .
Generic OBD II Diagnostic Trouble Codes
DTC CODES P0300 to P0399
P0300....Random/Multiple Cylinder Misfire Detected
P0301....Cylinder 1 Misfire Detected
P0302....Cylinder 2 Misfire Detected
P0303....Cylinder 3 Misfire Detected
P0304....Cylinder 4 Misfire Detected
P0305....Cylinder 5 Misfire Detected
P0306....Cylinder 6 Misfire Detected
P0307....Cylinder 7 Misfire Detected
P0308....Cylinder 8 Misfire Detected
P0309....Cylinder 9 Misfire Detected
P0310....Cylinder 10....Misfire Detected
P0311....Cylinder 11 Misfire Detected
P0312....Cylinder 12 Misfire Detected
P0313....Misfire Detected with Low Fuel
P0314....Single Cylinder Misfire (Cylinder not Specified)
P0320....Ignition/Distributor Engine Speed Input Circuit
P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance
P0322....Ignition/Distributor Engine Speed Input Circuit No Signal
P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent
P0324....Knock Control System Error
P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)
P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
P0330....Knock Sensor 2 Circuit (Bank 2)
P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332....Knock Sensor 2 Circuit Low Input (Bank 2)
P0333....Knock Sensor 2 Circuit High Input (Bank 2)
P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)
P0335....Crankshaft Position Sensor A Circuit
P0336....Crankshaft Position Sensor A Circuit Range/Performance
P0337....Crankshaft Position Sensor A Circuit Low Input
P0338....Crankshaft Position Sensor A Circuit High Input
P0339....Crankshaft Position Sensor A Circuit Intermittent
P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)
P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)
P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)
P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)
P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)
P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)
P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)
P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)
P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)
P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)
P0350....Ignition Coil Primary/Secondary Circuit
84 views
Usually answered in minutes!
×