Question about 1995 Ford Ranger Supercab

Open Question

How to replace cam sensor 95 ford ranger 2.3 - 1995 Ford Ranger Supercab

Posted by Anonymous on

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 23 Answers

SOURCE: 1998 ford ranger cam shaft sensor

there is a tool to line up the sensor while at top dead center on #1 cylinder you put it on top of the syncronizer fords name for the oil pump drive & interupter. good luck from schleck.

Posted on Sep 03, 2008

Ad
Armytech

Richard Schram

  • 47 Answers

SOURCE: 1997 ford ranger cam shaft position sensor

If you have the 3.0 L or 4.0 L V6 engine, the cam position sensor is located on the top rear of the engine. If you have the 2.3 L 4 cyl. engine, you will find it on the left front of the engine behind the oil pump pulley.

Posted on Sep 27, 2008

Anonymous

  • 59 Answers

SOURCE: 97 Ford Ranger 4.0L V6 Idles rough only when cold

Orand

Ther is a air Idle control valve located on the side of the throttle body. unplug it remove it spray it and clean it with carb cleaner replace it plug it back in and you will be a Happy person again.

Lugnut61

Posted on Feb 01, 2009

Anonymous

  • 22 Answers

SOURCE: need location of the erg sensor 2000 ford ranger

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Posted on Feb 25, 2009

localwonder

Michael Masters

  • 6784 Answers

SOURCE: most common cause for code P0340 of 95 Ranger

Hi, the cam shaft sensor will be located Under the hood, center, upper engine area, mounted behind rear of intake manifold, in the engine block.


This is a magnetic or hall effect sensor. It sends a signal to the computer relaying information about shaft speed, position and acceleration or deceleration. This information determines when the fuel/air mixture needs to be ignited and how much mixture is needed for the engine.

The possible causes of failure will be faulty housing or faulty wires as well. A faulty ECM could trigger a false alarm as well. this is highly unlikely but, possible in most cases. The most reported reasons is flat out sensor failure.

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 ford ranger dies going to take off what cause all electrics out wait 2 mins back on


Ford ranger died while driving, wont start. Hell - YouTube

? 1:43
www.youtube.com/watch?v=vvcq14hxUBw
Oct 17, 2013 - Uploaded by Pheonix_RessurectedSLT
Ford ranger died while driving, wont start. ... 1996 Ford RangerStarting Problem - one click, then nothing ...

Oct 29, 2015 | 2000 Ford Ranger SuperCab

1 Answer

Where is the cam sensor located on my 98 ford ranger.


It is located where the distributor would normally be.
cam-sensor-located-98-ford-ranger-nxmumukqemthcsnheggjjug3-4-0.gif

Oct 17, 2015 | Ford Cars & Trucks

2 Answers

Where is the cam shaft senser on a ford ranger 2.5 td 2002


Ford did not put a 2.5 in a Ranger, maybe a 2.3 ?
2.3 = 2007-01-27_154722_2.gif
3.0 - The CMP sensor& synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Jun 17, 2014 | 2002 Ford Ranger Regular Cab

1 Answer

Need to fix a camshaft position sensor on an 01 ford ranger 3.0


the cam sensor is located in the topside of the engine, behind the manifold, near the firewall. it is held in by two mounting bolts. just remove the wire connector and the two mounting bolts. you can then remove the cam sensor. slightly lube the oring on the new cam sensor and reinstall. tighten two mounting bolts and reconnect the wire connector

Mar 25, 2010 | 2001 Ford Ranger Regular Cab

2 Answers

Most common cause for code P0340 of 95 Ranger


Hi, the cam shaft sensor will be located Under the hood, center, upper engine area, mounted behind rear of intake manifold, in the engine block.


This is a magnetic or hall effect sensor. It sends a signal to the computer relaying information about shaft speed, position and acceleration or deceleration. This information determines when the fuel/air mixture needs to be ignited and how much mixture is needed for the engine.

The possible causes of failure will be faulty housing or faulty wires as well. A faulty ECM could trigger a false alarm as well. this is highly unlikely but, possible in most cases. The most reported reasons is flat out sensor failure.

May 21, 2009 | 2001 Ford Windstar

1 Answer

How to set the cam sensor


have you tried disconnecting battery for a few and reconnect...?

Apr 12, 2009 | 2000 Ford Ranger SuperCab

1 Answer

1998 ford ranger cam shaft sensor


there is a tool to line up the sensor while at top dead center on #1 cylinder you put it on top of the syncronizer fords name for the oil pump drive & interupter. good luck from schleck.

Sep 03, 2008 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...