Front wheel bearing torque 20

1995 C1500 spindle nut torque procedure? - CK5 Network

https://ck5.com > ... > General Discussion > The Garage
Jan 31, 2005 - while rotating the hub in a foward direction torque the nut to about 12ft lbs. Keep doing that a few times to ensure the bearings are seated.

96 gmc: torque..the front spindle nut..C1500 - JustAnswer

https://www.justanswer.com > Car Questions > GM Repair
Sept 16, 2011 - Torque nut (12) 10-12 ft lbs while turning the wheel assembly forward by hand. This will seat the bearing. Loosen nut (12) to a just loose ...
1 answer · Top answer: You can attach the magnetic base to the end of the spindle or to the brake caliper bracket. ...

• 
  

  1996 chevy: the torque setting for front wheel bearing..1500 4x4

  https://www.justanswer.com > chevy > 1tv6x-1996-che...
  Feb 18, 2009 - Outer Tie Rod Nut (C and K Models) · Shackle to Frame Nut and Bolt (C3500HD) · Shock Absorber Nuts (K Models) ; 62 N·m · 95 N·m · 90 N·m ; 46 lb ft.

Torque specification guide - PDF4PRO

https://pdf4pro.com > cdn > torque-specification-...
PDF
Front and rear axle nut torque specifications for FWD, RWD and 4 W/D vehicles. Torque specification guide. Form #457377. April, 2007.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

i usually put lock tight blue on them and tore to 65 ft lbs the nut on the axle i usually tore to 50- 60 ft lbs no lock tight

Front wheel bearing torque is usually about one uga dugga.

Better late than never Brucy....CLICK HERE TO SEE YOUR WHEEL BEARING GUIDE. Repair Guides Front Suspension Wheel Bearings AutoZone com

The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Front wheel bearing hub is 147 ft lbs. Axle nut is 170 ft lbs.

Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Lubricate the threads on the halfshaft with clean engine oil.
3. Remove or disconnect the following:
   • Front wheels
   • Halfshaft hub nut
   • Caliper from the steering knuckle WARNING
     DO NOT allow the brake hose to support the weight of the caliper.
     
   • Brake rotor
   • Anti-lock Brake System (ABS) sensor from the backing plate
   • Hub and bearing assembly from the backing plate
   • Hub and bearing assembly from the halfshaft
   • Hub and bearing assembly

To Install:
Exploded view of the front hub mounting and related components

1. Install or connect the following:
   • Hub and bearing assembly onto the halfshaft
   • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
   • ABS sensor
   • Brake rotor
   • Caliper on the steering knuckle.
   • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
   • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Front (4 Wheel Drive) To Remove:

1. Raise and support the vehicle
2. Remove or disconnect the following:
   • Tire and wheel assembly
   • Rotor (See: Disc Brake Rotor)
   • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
   • Electrical connection for the wheel speed sensor
   • Front drive halfshaft assembly (See: Halfshaft)
   • Hub and bearing assembly mounting bolts 4WD front hub
     
     
   • Hub and bearing assembly

To Install:

1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
3. Install or connect the following:
   • Hub and bearing assembly
   • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
   • Front drive halfshaft assembly (See: Halfshaft)
   • Electrical connection for the wheel speed sensor
   • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
   • Rotor (See: Disc Brake Rotor
   • Tire and wheel assembly
   Wheel lug nut tightening sequence
   
   
4. Torque the lug nuts to specification
5. Test drive the vehicle to confirm the repairs

112 to 174 ft lbs