Power window repair-How do I remove the quarter panel window motor?

You'll have to remove the window frame to replace. I don't work on yours. But you have to remove the door panel remove the regulator and motor. Remove the inside trim at the bottom of window and pull the widow out threw the top. Remove the bolts for the lower window frame, pull them down and out. The grab the front of the window trim in the door and start pulling it down. When you get to the quarter window you will need to pry down with a screw driver and pull down to get it out. Once it comes loose from the door it will drop. There will be screws or rivets that hold the bottom channel of the quarter window.

Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Remove plastic panel . Rear seats might have to be removed first. There are bolts and/ or rivets holding everything in place. There might also be a YouTube video on the subject. Good luck.

Rear Quarter Window Actuator - Right (A20)
Behind the right rear interior body panel
Rear Quarter Window Actuator - Left (A20)
Behind the left rear interior body panel
Rear Quarter Window Inoperative

1

Did you review the rear quarter window description and operation?
Go to Step 2
Go to Symptoms - Body Rear End

2

Verify that the rear quarter windows are inoperative.
Do the rear quarter windows operate normally?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

Are both rear quarter windows inoperative?
Go to Step 4 yes
Go to Step 6 no

4

1. Turn OFF the ignition.
2. Disconnect the rear quarter window switch.
3. Turn ON the ignition, with the engine OFF.
4. Probe the accessory voltage circuit of the rear quarter window switch harness connector with a test lamp that is connected to a good ground.

Does the test lamp illuminate?
yes Go to Step 5
no Go to Step 7

5

Connect a test lamp between the accessory voltage circuit of the rear quarter window switch harness connector and the ground circuit of the rear quarter window switch harness connector.
Does the test lamp illuminate?
Go to Step 8
Go to Step 10

6

1. Turn OFF the ignition.
2. Disconnect the appropriate rear quarter window actuator.
3. Turn ON the ignition, with the engine OFF.
4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
5. Activate the rear quarter window switch to the Open and Close positions.

Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

6

1. Turn OFF the ignition.
2. Disconnect the appropriate rear quarter window actuator.
3. Turn ON the ignition, with the engine OFF.
4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
5. Activate the rear quarter window switch to the Open and Close positions.

Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

7

Test the accessory voltage circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Retained Accessory Power (RAP) Inoperative in Computer/Integrating Systems

8

Inspect for poor connections at the harness connector of the rear quarter window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 12

9

Inspect for poor connections at the harness connector of the appropriate rear quarter window actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 13

10

Repair the open in the ground circuit of the rear quarter window switch. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

11

Repair the open in the appropriate power window motor rear vents control circuit. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

12

Replace the rear quarter window switch. Refer to Quarter Window Switch Replacement .
Did you complete the replacement?
Go to Step 14
--

13

Replace the appropriate rear quarter window actuator. Refer to Body Side Window Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--

14

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

You have to remove the Rear Panel, then the Window is bolted to teh Manual Window Regulator, Unbold and then pull out at an angle through the SLot

For the XL - The AMP is located on the drivers side, behind the left rear trim panel.

1. Remove the cargo shelf. 2. Tumble the third row seats to the cargo position. 3. Remove the left body side window rear garnish molding.4. 4. Remove the left body side window forward garnish molding. 5. Remove the liftgate sill plate. 6. Remove the left rear door sill panel. 7. Remove the lower seat belt anchor bolt. 8. Remove the auxiliary power outlet from the trim panel. Release the five screws that retain the rear quarter trim panel to the body. 9. Remove the rear quarter trim panel from the vehicle.

If you don't have the XL then the AMP is located on the passenger side.
1. Remove the screw that retains the trim panel to the body. 2. Remove the cargo net retaining knobs. 3. Remove the bolt that retains the seat belt upper guide to the body. 4. Remove the rear upper quarter trim panel from the vehicle. 5. Remove the cargo shade/cover. 6. Remove the inflator access panel. 7. Remove the right rear quarter upper trim panel. 8. Remove the liftgate sill plate. 9. Remove the right rear door sill panel. 10. Remove the lower seat belt anchor bolt. 11. Release the retaining clips that retain the trim panel to the body. 12. Partially remove the trim panel in order to remove the inflator switch from the inflator bezel. 13. Remove the auxiliary air outlet washer and retaining nut. 14. Feed the auxiliary air outlet through the inflator bezel. 15. Remove the inflator bezel from the trim panel. 16. Disconnect the the 12-volt power supply electrical connector. 17. Remove the 12-volt power supply. . 18. Remove the trim panel from the vehicle. 19. Disconnect the electrical connectors from the radio speaker amplifier. 20. Remove the 4 bolts that retain the radio speaker amplifier to the body. 21. Remove the radio speaker amplifier from the body.

from autozone.com:

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

   
   

Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.

j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.

k. Pull first rear seat belt through the access hole.

l. Remove the quarter trim panel from the vehicle.

3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).

4. Twist the blower motor out of scroll housing.

5. Disconnect the blower motor wiring connector.

6. Remove the blower motor from vehicle.


Fig. The rear blower motor is held in place by four screws
To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.
      
      
      

      Fig. Removing the trim panel to access the rear blower motor
      

   9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
   10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
   11. Pull first rear seat belt through the access hole.
   12. Remove the quarter trim panel from the vehicle.
       
3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
4. Twist the blower motor out of scroll housing.
5. Disconnect the blower motor wiring connector.
6. Remove the blower motor from vehicle.
   
   
   

   Fig. The rear blower motor is held in place by four screws
   

To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
       
6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004
Blower Motor - Removal & Installation

1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
2. Remove the glove box from the instrument panel.
   
   
   Fig. The blower motor is located behind the glovebox, behind the blower motor cover
   
3. Remove the A/C-heater blower motor cover.
4. Disconnect the blower motor wiring connector.
5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
6. Remove the blower motor mounting screws.
   
   
   Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing
   
   
   
   Fig. The blower motor is secured to the housing with three small screws
   
7. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
   

To install:

1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
3. Reconnect the blower motor electrical connector.
4. Install the A/C-heater blower motor cover.
5. Install the glove box into the instrument panel.
6. Reconnect the negative battery cable. Check blower motor operation.

Auxiliary Heater and Air Conditioner
Blower Motor - Removal & Installation

1. Disconnect and isolate the negative battery cable.
2. Remove the right quarter trim panel as follows:
   1. Remove first rear seat. Remove the second rear seat, if equipped.
   2. Remove the sliding door sill plate.
   3. Remove the quarter trim bolster.
   4. Remove the upper C-pillar trim and D-pillar trim panel.
   5. Remove the first and second rear seat belt anchors.
   6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
   7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
   8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.
      
      
      Fig. Removing the trim panel to access the rear blower motor
      
   9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
   10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
   11. Pull first rear seat belt through the access hole.
   12. Remove the quarter trim panel from the vehicle.
3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
4. Twist the blower motor out of scroll housing.
5. Disconnect the blower motor wiring connector.
6. Remove the blower motor from vehicle.
   
   
   Fig. The rear blower motor is held in place by four screws
   

To install:

1. Install the blower motor unit into the vehicle.
2. Reconnect the blower motor wiring connector.
3. Secure the blower motor into scroll housing.
4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
5. Install the right quarter trim panel as follows:
   1. Install the quarter trim panel in position in the vehicle.
   2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
   3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
   4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
   5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
   6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
   7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
   8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
   9. Install the D-pillar trim panel and upper C-pillar trim.
   10. Install the quarter trim bolster.
   11. Install the sliding door sill plate.
   12. Install the second rear seat, if equipped, and install the first rear seat.
6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember rated this).

give these peoples a call they sells only GM-parts Schram auto & truck parts the number is 1-800-292-1032