Need timing diagram for a 2003 Honda Accord I-VTEC 2.4

Find it on this site

https://www.felpro.com/technical.html

92-00 Honda Engine Swap Wiring Guide VTEC AND NON ...

honda-tech.com/.../92-00-honda-engine-swap-wiring-guide-vtec-non-vt...
Oct 8, 2011 - 92-00 Swap Wiring Guide for VTEC and Non-VTEC ... try to compile one thread that would try to answer pretty much 95% of all questions ... I wanted to do this because often times I end up posting the same thing to ... to ECU harness so using an EX/SI 92-95 engine harness will make VTEC plug and play.

97 accord non VTEC to VTEC ' HondaSwap

hondaswap.com > Model Specific > Accord
Jan 16, 2010 - 15 posts - ‎6 authors The distributors may be different on the vtec/non vtec. .... As was previously stated, allyou need to do is add wiring for VTEC. ... that connect to the ecu to the connectorsthat wire in your engine harness while the engine is out... f22b2 non vetec swap to f22b vtec need help asap
3 posts
Sep 22, 2012
96 accord head swap non vtec to vtec
10 posts
Jun 1, 2012
1990 USDM CRX Si D16A6 to ZC SOHC non-VTEC ...
20 posts
Mar 7, 2012
99 Accord non-vtec to vtec engine swap, need help
5 posts
Sep 27, 2011
More results from hondaswap.com

tHANKS I WILL TRY AUTO ZONE

CHECK VTEC SWITCH OIL PRESSURE.SHOULD BE 50 PSI @3000 RPM FOR THE S2000 OIL PRESSURE SHOULD BE 85 PSI @ 3000 RPM. IF OIL PRESSURE OKAY HAVE TO BE EITHER VTEC SWITCH FAULTY OR VTEC SOLENOID HAS FAILED.SOME TIMES PCM HAS FAILED TO THAT CONTROL CIRCUIT.

i have a honda accord 3.0 vtec and this is what i have Manual it works for me i hope i works 4 u 2 GOOD LUCK

hope this is what you were looking for. let me know if you need more!

http://www.wiringdiagrams21.com/2008/08/07/honda-prelude-iv-92-96-electrical-wiring-diagram

http://www.vidzshare.net/videos/EmasxgJdXJ8/how-to-change-timing-belt-in-a-vtec-honda-accord.html

Go to the above link and get a video explanation of how to replace timing belt in all accord with vtec engine...

1990-95 4-Cylinder Accord and 1992-95 Prelude




On all engines except VTEC, the belt adjuster arm must be locked in place using one of the lower cover mounting bolts




The balancer shaft must be held in position during timing belt installation




Timing belt and components used on the Accord V-6

I hope help you with this. Good luck (remember rated this help).

ok lets break this down
Vtec= Variable Valve Timing and Lift Electronic Control

if you look on the the motor on the left side youll see 2 things the distributor and the vtec solenoid.. the vtec solenoidif the smaller of the 2 thats it m8 theres 2 wires running from it .. all vtec does is lift the cams on a high 3rd lobe :) rides in the middle of the 2 smaller cam's on a automatic it should pop around 5.200 rpms on a honda ecu thats not tuned.. also a exaust helps or a intake that produce a higher tone thats unmistakeable when vtec hits.. its a beautiful thing hit me up with any! honda stuff ive done swaps to my 92 prelude si 2.2l vtec and many more so i know a honda engine and wireing like theback of my hand

If you are talking about just plugging into the speed sensor yes. A VTEC and NON-VTEC are one and the same.