Question about 2014 Chevrolet Silverado 1500

1 Answer

What does tvsa stand for - 2014 Chevrolet Silverado 1500

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 33 Answers

Magnuson super charger kits for your Chevy truck its a bolt on kit you can purchase comes with a charger all the brackets, belt, and software you will need to add a supercharger to your ride upend your horse power lower your mpg due to the fun factor you will have keeping up with the vette's and mustang's in your papa's pick up

Posted on Feb 11, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove Stand from Sharp LC 46D64U TV


Should be 4 screws that hold the stand into place. There is usually either a difference in the screws or some other identifier at the screw hole that differentiate from the other screws.

Oct 31, 2016 | Cars & Trucks

1 Answer

Where is the best place to put jack stands if I'm jacking up the front driver side


The intent of a jack stand is to provide safe solid support for the vehicle while you are performing work on it. Going under a supported vehicle at any time can be dangerous.
- I was taught to place jack stands under a frame or unibody support point, and NEVER under a suspension component that could move independently from the frame.
- Block wheels that are in contact with the ground to prevent the vehicle from moving forwards or backwards.
THE PARKING BRAKE OR GEARSHIFT "P" ARE NOT ADEQUATE.
- LOWER THE VEHICLE SO THAT ITS WEIGHT IS GRADUALLY APPLIED TO THE JACK STAND.
- WITH THE JACK STILL IN PLACE, GENTLY NUDGE THE VEHICLE TO MAKE SURE THAT THE JACK STAND IS SECURELY HOLDING THE WEIGHT.
- When using jack stands, the vehicle should be on a level surface, and evenly supported by jack stands of the appropriate size for the load being supported.

Apr 09, 2016 | Cars & Trucks

1 Answer

Put jack stands uder a 2001 Lincoln LS


place the trolley jack under the front cross member . (The big bit that connects the side frames under the sump). Lift as high as possible and place the jack stands under the chassis ( moulded rails ) where the sub-frame meets . Then place the trolley jack under the rear diff and lift as high as possible Place the jack stands under the chassis at the front of the springs or track rods By using these positions you will have the cabin securely jacked up with all the wheels free to remove or to work on. Before going under try rocking the vehicle hard to ensure that it will not move off the stands.

Mar 15, 2014 | Cars & Trucks

1 Answer

On one jack stand. Problems


Jack the car up, insert the jack stand and lower the car. Only put jack stands on one side of the car at a time.

Aug 20, 2012 | 1999 Porsche Boxster

1 Answer

What does the abreiviation rcu and gem stand for?


GEM stands for Generic Electronic Module. RCU stands for Rear Control Unit. Your in dash radio is just a faceplate. The audio unit is in the trunk.

Apr 30, 2012 | 1999 Mercury Sable

1 Answer

I own a 2000 toyota prerunner. My question regards changing a tire, both front and back. I can't tell where to place the jackstand. I see no "flat" areas ar "marked" areas to place...


In the front, place your jack stands on the stabilizer bar bracket that is bolted to the frame...
in the rear, put the jack stands on the rear end, closes to the outside as you can get...
Hope this helps ??

May 26, 2011 | 2000 Toyota Tacoma PreRunner

1 Answer

The function that rsiaes and lowers the vehicle doesn't work,


Lifting

The following instructions must be carried out before raising the vehicle off the ground.

  • Use a solid level ground surface.
  • Apply hand brake.
  • Select 'P' on automatic gearbox selector.
Note: If the propeller shafts are to be removed, reference must be made to the relevant operation. To avoid damage occurring to the under body components of the vehicle the following jacking procedures must be adhered to.

DO NOT POSITION JACKS OR AXLE STANDS UNDER THE FOLLOWING COMPONENTS:
  • Body structure other than approved jacking points
  • Bumpers
  • Fuel lines
  • Fuel tank
  • Brake lines
  • Front or rear suspension arms
  • Transfer box
  • Steering linkage
  • Front or rear differential units
  • Engine sump
  • Automatic gearbox
NOTE: For certain repair operations, it may be necessary to support the engine under the sump. In this case, a block of hardwood or a rubber block should be positioned on the jack lifting cup to protect sump. Vehicle jack
The jack provided with the vehicle is only intended for use in an emergency, for changing a tyre. DO NOT use the jack for any other purpose. Refer to Owner's Handbook for vehicle jack location points and procedure. Never work under a vehicle supported solely by the vehicle jack.

Hydraulic jack
A hydraulic jack with a minimum 1500 kg, (3,300 lbs) load capacity must be used.

WARNING: Do not commence work on the underside of the vehicle until suitable axle stands have been placed in their correct position. Always chock the wheels when jacking. The handbrake may be ineffective when the wheels are off the ground. Raising and supporting the vehicle
To assist in raising the vehicle, jacking points are provided as shown in the following illustrations.

Raising the front of the vehicle
Apply handbrake, select 'P' on automatic gearbox selector and chock rear wheels.
Axle stand positions - front

Raise vehicle to enable axle stands to be positioned under, either, the front sub-frame, or the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.
Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack.
Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Raising the rear of the vehicle
Select 'P' on automatic gearbox selector and chock front wheels.

WARNING: Always chock the front wheels when jacking the rear of the vehicle.

Axle stand positions - rear

Raise rear of vehicle to enable axle stands to be positioned under the rear sub-frame. Alternatively, the axle stands may be positioned under, either, the recommended customer jacking points or the front mounting points of the rear sub-frame.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If any damage occurs to the washers on the front mounting points of the rear sub-frame, then the washers must be replaced. Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack. Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Wheel-free lift
The following warning must be read before attempting to lift the vehicle.

WARNING: The vehicle cannot be supported safely in a wheel-free condition using the wheel-free facility of a four post ramp, and under no circumstances must this method be employedA wheel free condition may only be achieved on a four post ramp by raising each end of the vehicle and positioning axle stands beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox. WARNING: The front and rear suspension lower arms must NOT be used as lifting / jacking points. Alternatively, support the vehicle on an approved two post lift with the arms of the lift beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between the lifting equipment and the jacking points to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.

Oct 04, 2009 | 2003 Land Rover Range Rover

2 Answers

Jack stand spots?


that is the preferred place designed by the manufacturer

Sep 23, 2009 | 1992 Honda Accord

1 Answer

Can you tell me what lxi stands for on a 2001 chrysler sebring convertible please


Hi,

LXI - L stands for Base Model and XI stands for Petrol.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Sep 01, 2009 | 2001 Chrysler Sebring

1 Answer

Where is thermostat can it be changed using axle stands


The thermostat is attached to the radiator. I don't know why you'd want axle stands.

May 16, 2009 | 2002 Volvo S60

Not finding what you are looking for?
2014 Chevrolet Silverado 1500 Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...