2007 Honda Pilot Logo
A
Anonymous Posted on Jul 27, 2014
Answered

07 honda pilot keyless remote press buttons nothing works, new battery still nothing

Buttons pressed , led light doesn't light and door locks don't work

Answer This Question

1 Answer

Dan Hooper

Dan Hooper

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Honda Master 1,209 Answers
  • Posted on Jul 27, 2014
Dan Hooper
Honda Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Apr 20, 2013
Answers
1209
Questions
0
Helped
238195
Points
4234

Sounds like your key fob is either broken or the battery might be dead.

4 Related Answers

Anonymous

  • 105 Answers
  • Posted on Oct 25, 2009

SOURCE: 2003 honda pilot right rear door lock does not

if all others are working properly you are most likely having a problem with the door lock actuator in that door

Ad

Anonymous

  • 192 Answers
  • Posted on Apr 06, 2009

SOURCE: The key of my honda 2006 does not work upon

the key fob remotes need to be reprogramed or have the battery checked... make sure to have all key fob remotes present when reprogramming...

gfischer21

George Fischer

  • 236 Answers
  • Posted on Jun 17, 2009

SOURCE: 2003 Honda Pilot Door locks not working

may be a relay switch, or a faulty wire on the right side behind the glove box

Anonymous

  • 4803 Answers
  • Posted on Nov 08, 2009

SOURCE: Power door locks do not work with keyless remote control

There are two multiplex control units - one on the driver side and one onthe passenger side - which one did you unplug? The one on the driver side is the main "Brain" while the other one is the one that houses the keyless reciever. According to the service manual, any troubleshooting of this system must begin with the one on the driver side. It can get quite involved because Honda does not provide actual troubleshooting (symptom) charts, just descriptions of the electrical connectors and what conditions should be present at each conector pin under what system condition. (each pin has to be tested to determine what is malfunctioning) The system is not capable of outputting fault codes of any kind.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

What is wrong with my hummer H3 locks. Neither the keyless remote nor the lock button from the door can open all the passenger doors. When I press the Keyless remote or the door lock button, it open the...
Check the relays in the fuse box. It appears that the solenoids for locking the doors are working correctly. However it appears that the lock solenoid is not working properly.
Read full answer
Jan 30, 2015 • 2007 Hummer H3
1helpful
1answer

How do you program the transmitter on a 1996 Lincoln Town Car?
1. Enter 5-digit permanent entry code into the keyless entry keypad.
2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.
3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.
4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).
5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.
Read full answer
Mar 28, 2013 • 1996 Lincoln Town Car
0helpful
1answer

2008 Volkswagen Jetta keyless entry & lock problems
If the system is not working even when you press the buttons on the door, then the problem is not with the remote control. I would first check if all the fuses are ok, if they are, I would check the wiring on the door to make sure there are no wires broken of chaffed. Focus first on getting the system working with the door buttons and after that is ok, the move on to the keyless system in case it still does not work. Hope this helps.
Read full answer
Dec 29, 2017 • 2002 Volkswagen Jetta TDI
0helpful
1answer

I have a cool start remote engine starter and keyless entry...I changed the battery in both remotes and they worked fine for about a month and then none of the buttons work except for the light when i push...
Have you tried to change the batteries again?
Read full answer
Dec 10, 2017 • 2003 Chrysler 300M
0helpful
1answer

How do you prgram remote keyless entry
Here are the instructions from the factory service manual:
1. Enter 5-digit permanent entry code into the keyless entry keypad.
2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.
3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.
4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).
5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.
Read full answer
Sep 14, 2011 • 1995 Ford Crown Victoria
0helpful
1answer

My keyless remote doesn't work anymore to open my car doors an to set alarm, while walking away to or from vehicle...bought new battery for remote an it still doesn work...have to lock an unlock by hand...
before you spend too much money...try this.
On the inside of the keyless remotes, there are rubber buttons, those rubbers buttons are brushed with metal of some sort so that it reacts with the motherboard, when the remotes get older this metal wears off...so try this, it worked for me...
I superglued foil paper to the back of the button (the parts that touches the motherboard when pressed) and replaced the batteries... it worked like a charm, I used an awl and a hammer to make perfectly round piece of foil and just glued it onto the back of the button... i'd try this first before spending any real money.
Read full answer
Oct 10, 2010 • 2000 Mitsubishi Montero
1helpful
1answer

Keyless entry on my 2001 Taurus suddenly stopped working (both remotes). I replaced batteries and also tried reprogaming (off/on 8 times. The doors lock/unlock indicating the programing is working, but...
dealer reflash
Read full answer
Aug 31, 2009 • 2001 Ford Taurus
1helpful
1answer

I need to program the key fob
. Enter 5-digit permanent entry code into the keyless entry driver door keypad. 2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.
3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.
4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).
5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.
Read full answer
Jun 29, 2009 • 1997 Mercury Grand Marquis
1helpful
2answers

1999 lincoln con
SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code
  1. Enter the permanent factory keyless entry keypad code.
  1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.
  1. Enter the new five-digit keyless entry keypad code.
  1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.
  1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.
  1. After all new keyless entry codes are programmed:
    • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
    • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
    • -------------------------------------------------------------
Programming —Transmitter
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------
Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.
  1. Press the SET button on the driver door panel.
  1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.
  1. Press the 1 or 2 memory button on the driver door panel.
-------------------------------------------------------------
Programming —Autolock and Horn Chirp
  1. NOTE: This procedure must be completed within 30 seconds.
    Turn the ignition switch to RUN.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to OFF.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.
  1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.
  1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.
----------------------------------------------------------------------------------
Read full answer
Apr 07, 2009 • 1999 Lincoln Town Car
4helpful
1answer

Reset keyless entry on 1998 honda civic
Okay, here goes-

1. Turn Key to on position.
2. Push and hold **valet button on the stock radio.
**Valet button is skinny bar located between am/fm & cd/tape buttons on stock radio.
Door locks will cycle one time.
3. Press any button on remote one time within 20 seconds. Door locks will cycle again.
4. To program up to 4 additional remotes repeat step 3 for each additonal remote.
5. Turn key off programming is complete.

Thanks for using Fixya, please rate if this helps :)
Read full answer
Mar 16, 2009 • 1998 Honda Civic
Not finding what you are looking for?

View Most Popular

2007 Pilot

  • Cars & Trucks

Related Question

What is wrong with my hummer H3 locks. Neither the keyless remote nor the lock button from the door can open all the passenger doors. When I press the Keyless remote or the door lock button, it open the...

  • 2007 Hummer H3

Related Topics

605 views

Ask a Question

Usually answered in minutes!

Popular Questions

Honda pilot emissions warning light

2009 Honda Pilot

What does the warning light of a yellow triangle

2005 Honda Pilot

VTM-4 indicator light comes on

2005 Honda Pilot

How do you shift into neutral when battery is

2007 Honda Pilot

What does service code A136 for a 2006 Honda Pilot mean?

2006 Honda Pilot

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. 2007 Pilot Manual

2007 Pilot

Loading...