Anonymous Posted on Jul 28, 2014

Keyless ignition and clock display etc not working

My husband changed the radio and something pinged when testing the voltage with the meter. We can start the engine with the key but not keyless and the doors do not lock. No dash lights apart from the power steering symbol comes on and the clock, temperature, Km display no longer works? Any ideas

1 Answer

aaron woods

Contributor 8 Answers
Posted on Jul 28, 2014

aaron woods

Contributor

Joined: Jan 20, 2012

Answers

Questions

Helped

3339

Points

He shorted it you will need to take it to a garage

4 Related Answers

Boyet Soriano

293 Answers
Posted on May 28, 2009

SOURCE: remote key fob does not unlock or lock car

It may just be a battery problem. Replace the battery of your remote fob. If it will not work, try to reposition the controller beneath the dashboard.

Anonymous

20 Answers
Posted on Jan 23, 2010

SOURCE: can't find the fuse box under the driver's side dash on my 2000 suzuki grand vitara. my radio/clock not working and dome light does not come on when the driver's side door is opened.

Its below the Dashboard, on the left side of your knee. You have to use a torch & locate it from under the Dashboard, Its roughly near to the Clutch Pedal.
Here, it looks like this: (The Black one is the Fuse box)

Anonymous

10319 Answers
Posted on Mar 27, 2010

SOURCE: 2006 grand vitara - steering wheel locked - ignition wont turn

It sounds like sticking lock tumblers since beating on it seems to make it work once in awhile. No other items in the column will die out and work again upon pounding on it

Anonymous

1 Answer
Posted on Mar 27, 2011

SOURCE: After changing battery in 2004 Suzuki Verona key

had the same problem in my 2004 verona.look under your dash below your steering wheel.you will see a small fuse box with fuses on the very bottom of it.look for the yellow 5amp fuse which will be blown.change that baby out with a spare fuse and pow!everything is good again and u didnhave to spend more than 2.00 for a fuse lol.ets get it donelet us check back with us afterwards

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

2000 Ford Excursion radio will not shut off with key in hand

The fuses are for base radio system. With key out, check the two outside fuse circuits for voltage. Shouldn't be any voltage, if there is, have to check ignition switch wiring circuits. Use a test lite to check for voltage
The fuse in the middle, hot all the time, should be for radio memory and clock where applicable.
base radio fuses-atz0hg4qofldc3jv0oleu0mk-3-0.jpg

base radio fuses-atz0hg4qofldc3jv0oleu0mk-3-0.jpg

Read full answer

Mar 14, 2017 • Ford Cars & Trucks

0helpful

2answers

2001 gmc jimmy clock stays on after door is opened and dies out battery, what could be wrong?

No other lights on ,dome, courtesy etc...
Battery Rundown Protection/Inadvertent Power
In the event that any of the interior lamps supplied voltage by the inadvertent power relay and ground from the courtesy lamp relay were to remain on when the ignition is OFF after a period of 20 minutes, the BCM will deactivate the inadvertent power relay turning OFF all of the lamps on that circuit to prevent total battery discharge. Only when the ignition switch is cycled back to the RUN position will the BCM reset the internal timer and reactivate the inadvertent power relay. When the inadvertent power relay is not energized, the BCM utilizes the inadvertent power courtesy lamp supply voltage circuit to monitor for a courtesy lamp switch request signal. If a courtesy lamp switch is activated, the BCM will receive the signal to energize the inadvertent power relay by grounding the control circuit.
It maybe your radio !
It may

Read full answer

Sep 06, 2015 • 2001 GMC Jimmy

0helpful

1answer

No power unless key is in ignition.

Take it to a store that installs remote starters and stereo amps.

Read full answer

Aug 18, 2017 • Mitsubishi Endeavor Cars & Trucks

0helpful

1answer

2005 chevy silverado 1500 the radio, windshield wipers, indicator lights and heater controls don't work all fuses are good and have already changed ignition switch all fuses give a dime light on

Do you know what a automotive electrrical wiring diagram is ? How to use a DMM- digital multi-meter ? Pick one system an diagnose an you will probably fix all the syatems . Voltage drop testing . Voltage or ground side problem .
Mastering Voltage Drop Testing with Pete Meier and Jerry Truglia
Free wiring diagrams http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size. View wiring diagrams an test the circuits.

Read full answer

Mar 06, 2018 • Cars & Trucks

0helpful

1answer

Hi there lm trying to work out which fuse is for the radio and the light behind the clock

one way would be to remove and replace fuses and see which one causes the radio to lose power.
if no radio connected then connect a voltage test meter to the connecion and test.

Note~ some radios have an anti theft device fitted which activates if the radio loses power.
be sure you have your security code available to gain access once the radio gains power again.

I hope this was useful

Read full answer

May 23, 2011 • Toyota Corolla Cars & Trucks

0helpful

1answer

94 grand cherokee baterry goes dead after sitting 5 days starter clicks and flashers flash. recharged battery will last another 5 days,

battery could be at fault or there is a draw in system that pulls down battery
have battery tested and leave it disconected for a few days then reconect to see if vehicle starts
if it does battery should be o.k. next is there any thing that stayes on (aftermarket stuff)
that may cause a draw on system if thats ok need to performed parasetic draw on system
hook up voltage meter between positive cable and meter
on 20 volt schale put red wire of meter to battery positive post black wire to red wire that was hook to battery voltaged should be minimal only to keep computers alive (clock - radio preset-etc etc)
if draw is high start removing fuses in system one at a time and check the voltage meter until it drops
you have now located the faulty cicuit that that fuse feeds start looking in those area
also feel starter selenoid and alternator at rear to see if they feel warm thet could be partly switch on
killing the battery over time
good luck

Read full answer

Apr 01, 2011 • 1994 Jeep Grand Cherokee

0helpful

1answer

My Escape Radio, CD, and Aux input will not work. My temp gauge works, but all music controls do not, except for the load and eject buttons for the CD player. I replaced three fuses that according to my...

Which three fuse's did you replace ? You should check for B+ voltage on both side's of the fuse . Two little metal tabs on top of the fuse. Voltage on both , fuse is good .
Try radio self-diagnostic mode .
A fluctuating AC voltage audio signal is sent to the speakers directly from the audio unit to reproduce sound. The audio unit has a self-diagnostic mode that can be entered by pressing preset buttons 3 and 6 simultaneously.
Visual Inspection Chart Mechanical Electrical

Audio unit
Antenna or antenna cable
Speaker mounting/speaker cones
Radio ignition interference capacitor, radio frequency interference suppression bond, or radio receiver hood bonding strap

Smart junction box (SJB) fuse(s):
- 7 (10A)
- 12 (5A)
- 16 (15A)
Battery junction box (BJB) fuse(s):
- 7 (40A)
- 15 (20A) (Hybrid)
- 16 (25A)
- 21 (40A)
- 22 (40A) (Hybrid)
- 23 (40A) (Hybrid)
Subwoofer amplifier
Circuitry
Audio unit

If the concern is visually evident, GO to Symptom Chart .

If the concern is not visually evident, proceed to the Speaker Walk-Around Test and the Audio Unit Self-Diagnostic Mode.

Speaker Walk-Around Test (Except Premium CD6)
NOTE: To enter the speaker walk-around test or audio unit self-diagnostic mode, the audio unit must be turned on and in the radio tuner mode (AM/FM).

To enter the speaker walk-around test, simultaneously press the audio unit preset buttons 3 and 6.

The speaker walk-around test stops at each speaker and applies sound to each speaker for about 1-2 seconds. Each speaker is tested and displayed on the audio unit in the following sequence: RF, LF, LR, RR and SUBWOOFER.

To exit the speaker walk-around test, turn the ignition switch off, turn the audio unit off, or press preset button 1 for diagnostics (DIA).

Audio Unit Self-Diagnostic Mode (Except Premium CD6)
NOTE: To enter the speaker walk-around test or audio unit self-diagnostic mode, the audio unit must be turned on and in radio tuner mode (AM/FM).

To enter the following tests, press the desired preset button while in the speaker walk-around test or while in the audio unit self-diagnostic mode.

To exit the audio unit self-diagnostic mode, turn the ignition switch or the audio unit off.

If the concern remains and the fault is not detected, GO to Symptom Chart to continue diagnostics.

The self-diagnostic mode has 6 manual tests available:
- Preset button 1 = ENTER DIAGNOSTICS. This test enters diagnostics from the speaker walk-around test. Metrics are available with SEL and ON buttons indicating time played in AM/FM, media, number of buttons pressed, etc.
- Preset button 2 = EEPROM BLOCK STATUS. This test shows the validity of memory to calibrate the clock, and seek sensitivity.
- Preset button 3 = EXIT DIAGNOSTICS.
- Preset button 4 = Software configuration level. This test queries each radio system controller for its software configuration level.
- Preset button 5 = DISPLAY TEST. This test lights all the display segments for five seconds and then turns all segments off.
- Preset button 6 = RAM CONTENTS READOUT. To enter these tests, press preset button 1 while in the speaker walk-around test, then the desired preset button.

To exit the self-diagnostic mode, turn the audio unit or the ignition switch off.

If the concern remains and the fault is not detected, GO to Symptom Chart to continue diagnostics.

Read full answer

Oct 06, 2017 • 2008 Ford Escape

0helpful

1answer

What yellow wire is the ignition wire for the radio?

ignition wire will have battery voltage with the key on. speaker wire will not have voltage. You can check with volt meter or test light.

Read full answer

Jul 29, 2009 • Oldsmobile Cutlass Ciera Cars & Trucks

3helpful

2answers

CLock, radio, dome lights, speedometer, keyless entry dont work

Check fuse 8 (10 amp fuse) in the under dash fuse panel. Make sure you have voltage to it on both sides of the fuse.This fuse feeds all of the items you listed.

Read full answer

May 25, 2009 • 1995 Ford Mustang

0helpful

2answers

Unstable electrics resulting in various problems.

Sounds like another VW made in Mexico.
Have the ECU checked for shorts, it sounds like it needs replacement.
Also check your vacuum hoses for leaks.

Read full answer

Feb 16, 2009 • 2000 Volkswagen Golf

Not finding what you are looking for?

View Most Popular

2007 Swift 1.3

Cars & Trucks

2000 Ford Excursion radio will not shut off with key in hand

Ford Cars & Trucks

459 views

Ask a Question

Usually answered in minutes!

Check Out the Latest Top Trucks Report!

View all Fixya Reports

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for 2007 Suzuki Swift 1.3? Or just drag it here!

Related Topics:

Keyless ignition and clock display etc not working