Ford Mondeo Mk3 Estate 2L. Air bag / seat belt Warning Light

Question edited for three uses of the word 'booth', changed to 'boot. As it is a Mondeo, I presume you are in the UK?

Look for a button in the glove compartment that is a child lock and stops the boot being opened from inside the vehicle. The fuse box doesn't show fuses or relays for it. Sometimes there is a slide switch on the inner side of the lock.

Ford Mondeo (2000 - 2007) - fuse box diagram - Auto ...

https://www.autogenius.info > ford-mondeo-mk3-fuse-...
May 25, 2015 - Ford Mondeo (2000 - 2007) - fuse box diagram. Year of production: 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007 ...

2000-2007 Ford Mondeo MK3 Fuse Box Diagram

https://knigaproavto.ru > shemy > 477-2000-2007-ford...
Dec 4, 2017 - Fuse Box Layout Ford Mondeo with engine: 1.8L, 2.0L, 2.2L, 2.5L and 3.0L (Mk3 - saloon, liftback, estate; 2000, 2001, 2002, 2003, 2004, 2005 ...

..

Adjust the switch a little?

Please follow link and read about code Airbag flash 24

REPAIR PROCEDURE FOR AIRBAG FAULT CODE 24 Security Safety Mk3 Mondeo

A bad seat belt switch inside the buckle, try some tuner cleaner from best buy or radio shack

The airbag light is probably an issue with the connector under your front seats. Look under the seats and you'll see the cables. Do NOT disconnect them. Just push them in tight. See if the light problem goes away. The conenctor gets off kilter when you put the head rests (from the back seat) under the front seat. Toss them in the back from now on.

BTW: You can get the computer to tell you the problem code with the air bag simply by watching the airbag lamp flash when you turn the key to 'on'. It will flash with short and long pauses. Count the flashes for each digit. For instance, 4 quick flashes, a pause, and then 3 flashes equals code 43. Then do a Google search of ford airbag code /your number here/. Odds are its the passenger side airbag connector. Do what I said above.

If you get tempted to disconent the cable, PLEASE do some google searching first. I 'think' this could cause a problem. Maybe not. But I only needed to push my connector in tighter to fix my problem.

its telling you theres a code in the system. need to have it scanned to see what the code is

hallo
if your foult is driver side airbag and it is not blown out, you should check "clock spring" wires behind steering whell.
if foult is driver side belt tensioner, check conector underneeth driver seat.
on the end erase foult/s with diagnostic equipment.
Marko

first, you need to read the Lamp Fault Code, LFC from the flashing light. Here's how:

Lamp Fault Codes
When the restraints control module (RCM) detects a system fault, it will cause the air bag indicator to flash a coded sequence: a lamp fault code (LFC). The code is two digits. The first digit is flashed with a 0.5 second interval between pulses. There is a 2 second pause before the second digit is flashed, which also has a 0.5 second interval between pulses. There is a 5 second pause between each display of an LFC.
Each LFC is flashed five times after which the air bag indictor will remain lit for the remainder of the key-on cycle. If there are multiple LFCs, each LFC will flash in order of priority.
-------------------------------------------------------
The fault could be in the air bag circuits, the canopy circuits, the pretensioner circuit on the seat belts, etc.
Report back with code.

here's some of system.

SECTION 501-20B: Supplemental Restraint System 2003 Expedition/Navigator Workshop Manual
DESCRIPTION AND OPERATION Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants in addition to that provided by the three-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles can also be equipped with optional safety canopies that deploy from the A-pillar to the C-pillar upon a side impact or if a rollover condition is detected. If equipped with safety canopies, a unique restraints control module (RCM) is used.
See the following illustration for deployable component location.
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) Deployable Components Item Part Number Description 1 611D10 Passenger air bag module 2 042D94 Passenger side safety canopy module 3 042D95 Driver side safety canopy module 4 61203 Driver safety belt buckle and pretensioner 5 043B13 Driver air bag module 6 14A664 Clockspring 7 61202 Passenger safety belt buckle and pretensioner


Item Part Number Description 1 14B321 Restraints control module (RCM) 2 14B345 Second row, C-pillar side impact sensor 3 14B345 Second row, C-pillar side impact sensor 4 14B416 Driver seat track position sensor 5 14B345 Front row, driver door, side impact sensor 6 14B006 Front impact severity sensor 7 14B345 Front row, passenger door, side impact sensor

the computer probably just needs reset because the seat belt warning feedback is tied in to airbag system. try disconnecting the neg battery terminal for about 5 min

Hi, ON your 2002 ford taurus, The Flashing code 33 ( B 2292 )

This code refer to : Driver side seat belt pretentioner ( seat belt bucklet) problem.

Check the conecctions under the driver seat.
Repair as need, and recheck if thi code is present.

But if you had an accident on you taurus. You need to replace the Seat belt Pretentioner ( seat belt bucklet)

OK. I hope this information work for you.

Than's.