2000 Isuzu Trooper Specs

The rod bearing cap bolt torque specifications for the 3.0L V6 engine in a 2000 Ford Ranger XLT 4x4 with a manual transmission are as follows:

• Step 1: Tighten the bolts to 15 foot-pounds of torque.
• Step 2: Tighten the bolts to 30 foot-pounds of torque.
• Step 3: Tighten the bolts an additional 90 degrees (1/4 turn) using a torque angle gauge.

It's important to follow the torque specifications and sequence in the manufacturer's service manual to ensure proper tightening and prevent damage to the engine.

Hi Joe

51 foot pounds

2000 Toyota solara 2.2L Engine Torque Specs

https://toyota-specs.com > cars > torque-specs_engine

Toyota Camry Solara Alternator Torque Specs : 18 ft-lbs ; Belt Tensioner Torque Spec, 51 ft-lbs ; Motor Mount (Engine Side) Torque, 59 ft-lbs ; Motor Mount (Frame ...

it is Newton meters / foot lbs. 162 is metric and 220 is US

What are the torque specs for the rod bearings on a 2006 - Fixya

https://www.fixya.com > ... > 2006 Dodge Caravan
Nov 15, 2019 - What is the torque specification for the inner tie rod 1996 .dodge caravan 2.4 liter. 45-55 foot pounds. Read full answer. Sep 18, 2012 • 1998 ...
SOLVED: Torque chart for dodge caravan 4l - Fixya
Sept 9, 2019
Main bearing torque spec for Dodge Grand Caravan 2005
Sept 15, 2019
Im trying to find the connector rod bearing torque - Dodge - Fixya
Jul 15, 2018
Head bolt torque specs for 2.4L dohc dodge caravan - Fixya
Jun 2, 2012
More results from www.fixya.com

Dodge Caravan 2.4 need engine tightening specs and head ...

https://www.justanswer.com > chrysler > 28qv6-dodge-...
Jun 27, 2009 - SPECIFICATIONS - TORQUE ; Balance Shaft Carrier Cover-Bolts, 12, - ; Camshaft Sprocket-Bolt, 101, 75 ; Connecting Rod Cap-Bolts, 27 +¼ turn, 20 +¼ ...
1 answer · Top answer: Here are the head bolt specs: Before installing the bolts, the threads should be coated with ...

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. CASE. 2.4. 148. 61-66. 45-50 FT/LBS. 90-100 FT/LBS. 60-65 FT/LBS. CASE. 2.4.
124 pages
You've visited this page 3 times. Last visit: 01/02/22

already answered here, 26 or 29 :>D

What are the torque specs for crankshaft main and rod - Fixya

https://www.fixya.com > ... > Buick > LeSabre
Sept 21, 2012 - The connecting rods torque to 29 foot pounds. ... Where is the eng control module in a 2005 Buick Rendezvous ultra 3.6 eng.
SOLVED: I need torque specs. for rod bearings and main - Fixya
Jun 2, 2011
Torque specs for intake on 2005 buick rendezsous - Fixya
Sept 7, 2019
Torque spec for1997 3.8 buick rod and mains - Fixya
May 22, 2012
What is the torque specks for a 3.8 lt v 6 rear main cap 1987 buick ...
Nov 14, 2019
More results from www.fixya.com

More here

https://www.google.com/search?q=05+Buick+Rendezvous+Ultra+3.6+piston+rod+torque
..

according to the manual (Chiltons).
#1 YOU MUST USE NEW ROD BOLTS AND NUTS !!!!
#2 TORQUE TO 17 FOOT POUNDS !!!!
#3 TORQUE TO 32 FOOT POUNDS !!!!
#4 TIGHTEN AN ADDITIONAL 90 TO 120 DEGREES !!!!
#5 DONE.

See #1; Main bearing diagram
See #2; NM conversion chart

1. NOTE: The crankshaft must rotate freely; if necessary check and adjust the bearing clearances.Tighten the main bearings and connecting rod bearings.
   
   1. Tighten the main bearing bolts in two stages.
   • Stage 1: 25 Nm.
   • Stage 2: 60 degrees.
   1. Tighten the connecting rod bearing bolts in two stages.
   • Stage 1: 25 Nm.
   • Stage 2: 90 degrees.

# 2) Newton Meters conversion chart:
http://extraconversion.com/energy/newton-meters/newton-meters-to-foot-pounds.html

#1)
saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

main bearing caps 56-62 foot pounds connecting rod caps 1st pass 17 foot pounds 2nd pass 32 foot pounds......................HAVE FUN

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using FixYa. Roger